66517054402 Kenmore Dishwasher - Instructions

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

I read online about a few other people who had the blinking light problem. Suggestions were to press a series of other buttons in sequence. Didn't work. I went to the advice website and paid $24 to be told it was the control board. I ordered a control board. As I was preparing to install it, I noticed a black spot on the ribbon connector that was across two of the printed (?) flat wires. I gently scraped it off. It was shorting the two flat wires. I put it all back together with the old board, and all is working well. It's been a week.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

Remove and replace solinoid, remove and replace mico switch. These are the only two electrically controlled devieces controling water flow. Replacing switch without replacing housing takes a soft touch. A small screw driver helps. Electrical connections have a stay in place nipple. Plyers help get thoes off.

Parts delivered as promised, correct fit. Phone contact available at order question.

Would used this site again.

grade 3.5 A=4

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

easy as long as you have the right tool to take the panel off, maybe they could include one for people who don't have a good selection of tools. Thankfully we did.

Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!

put new hose on, very easy.

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

Replacing the float switch was fairly easy and straight forward. removed old using adjustable wrench and replaced.

Replacing the door links was not difficult except I needed to pull the dishwasher out and had to disconnect the water line.
reconnecting the water line was the time consuming and frustrating part. Once that was hooked up and tested, i pushed the dishwasher back in place and all is good again.

1. Opened inside panel (about 8 screws)
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!

removed rack
removed one screw
removed old seal
installed new seal
installed screw

Pulled out the screws to the panel. Did a visual inspection and noticed a burn mark on a terminal on the circuit board. Replaced the board and now had no lights. Made sure the breaker wasn't tripped and than followed power through the dishwasher and it went to the fuse on the circuit board that you have to take from the old board and put it on the new board. Well anyway, the fuse was blown and had to get one of them. Now dishwasher works.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit