58714019406A Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Warren, PA
- Parts Used:
- A00104102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door handle broke from latch
Removed the 6 screws from top section inside door. Pulled control panel from front side of door. Removed two screws holding latch assemly unit and pulled 4 wires from connection. Attached the 4 wires to new door latch assembly and screwed back into place. Replaced the control panel and attached with 6 screws. Couldn't get any easier.Great service Quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Bridgeton, NJ
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from OAKLEY, CA
- Parts Used:
- 5304535380
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Changed out upper rack
Replaced upper wash blade and used screwdriver to pop off rail stops to slide rack all the way out to exchange
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from PT CHARLOTTE, FL
- Parts Used:
- 154290204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishes were not getting clean, always had a film on them and dishes didn't dry.
I removed the kick panel at the bottom front of the dishwasher. Then using a flashlight and a cross point screwdriver, I removed the thermostat from about the middle left. It requires a short screwdriver, but not quite as short as a stubby. I unplugged the wires, noting that one of them was a little burnt looking. The burnt looking connector was still okay. I then installed the new one, with the green dot on the thermostat having the slightly burnt looking connector. Then I ran a load of dishes and the dishwasher worked as it was supposed to. It has worked okay twice since then.
Was this instruction helpful to you?
Thank you for voting!
Noisy, vibrating pump
After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.
I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.
I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from beasley, TX
- Parts Used:
- A00126501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
not draining
fixed it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Los Angeles, CA
- Parts Used:
- 154574401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher Detergent Dispenser broken
1 Removed 2 screws to remove door panel so as to access back of dispenser.
2 Unplugged 2 color-coded wires attached to dispenser
3 Removed 6 screws attaching the dispenser.
Reversed these 3 steps to install new unit.
Easy. Don't even think of calling the repairman.
2 Unplugged 2 color-coded wires attached to dispenser
3 Removed 6 screws attaching the dispenser.
Reversed these 3 steps to install new unit.
Easy. Don't even think of calling the repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from PALM SPRINGS, CA
- Parts Used:
- 809006501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The bottom door gasket was loose and leakage was occurring from the door
Followed the YouTube instructions. Loosened 4 screws took off the front door panel and removed the old door and installed the new one. The video was very helpful!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Lakewood, WA
- Parts Used:
- 154637401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
no water entering the dishwasher
turned off electricity, pulled dishwasher out about a foot, turned off water too dishwasher, removed inlet valve and replaced it with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from TREVOSE, PA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dispenser cover wouldn't stay closed
Removed two screws,one on each side of the bottom part of the door. The door cover then comes off. Then 6 screws hold on the dispenser. Shut off power and remove two wire connections. Replace dispenser. Replace lower door cover and two screws. Done.
Was this instruction helpful to you?
Thank you for voting!
Missing tub gasket
I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from La Mirada, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BAY SHORE, NY
- Parts Used:
- 154430501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Spring broke
Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Milford, MA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish washer leaking at the door
Pulled off the old gasket and replaced it the same way with the new one.
Was this instruction helpful to you?
Thank you for voting!
fin in pump broke
pulled out dishwasher ,left lines hooked ,started cicle .heard pump.took apart.seen problem. order new one ,works like new..
Was this instruction helpful to you?
Thank you for voting!