66517749K010 Kenmore Dishwasher - Instructions

Disconnected the power and hot water supply.
Removed mounting screws under the counter, and the lower panel screws to expose the leveling screws.
Backed the leveling screws up so that the unit would slide out more easily
Walked the unit out to where I could reach the back side.
Disconnected the two power wires from the heater coil (slide off)
Unscrewed the plastic nuts holding the heater in place and removed the heater coil.
Replaced the heater coil and nuts.
Reversed the process above to install.

The first thing I did to repair my diswasher was call a repair company. They wanted $175.00 just to look at it, so I scheduled an appointment. Then, I did an internet search for dishwasher repair. I learned about bi-metal fuses, and how to check them. I found my bi-metal fuse was bad, so I ordered a new one through parts select. My part arrived in two days. I installed it easily, and the dishwasher worked. Finally, I canceled the repair appointment.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.

Make sure you order 2. One on each side

I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

Remove front door panel, replace B-metal fuse.

Replace motor/pump assembly

Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.

Very easy repair !!! I ordered my heating element on a Friday , it was on my porch Saturday. I used the directions that Parts.com sent me . I also read everyones Installation instructions ..... Every step was very easy . I did watch a utube video , so I couldn't screw this repair up......... My wife had a new dishwasher picked out for $ 579.00 , my part was $29 dollars , savings $550 dollar ...... After the repair , I ran the dishwasher and the blinking clean lite took care of itself ... The water has never been this hot and dryers the dishes like it was a new dishwasher ...... My advice , read everyone's Installation instuctions and watch the utube video .....

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.