66516052402 Kenmore Dishwasher - Instructions

I had a repair guide for my dishwasher which helped. First I removed the water distribution system inside the dishwasher and then removed the door panel. Next I removed the front bottom access panel. I placed a pan under the pump and hoses to catch water when I removed the outlet hose. Very important here! One must remove the pressure switch from the outlet port or else you can't get the pump clear of the washer tub. Next I removed the drain pump by releasing the catch and turning the pump counter clockwise. Now for one of the hard steps. I had to remove three pins which hold the pump assy to the wash tub. Two of them are out of sight so you have to weave you hand past all the hardware and "feel" for the back two. At this point the pump assy just lifts out. Remove the motor /pump by removing one bolt and turning it counter clockwise and withdrawing. I put the new one in. Don't forget to put the pump screen in as I missed this and had to redo the job. Reverse all the previous steps being careful to keep the motor guard out of the pump seal area. Use lots of silicon seal grease and check for leaks on first power up. It took me a couple of adjustments to get a leak-free seal.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

1, I shut off ac circuit breaker.
2.Shut off water supply valve.
3.disconnected water line from inlet valve.
4. disconnect the drainage hose.
5. have plenty of towels to mop up water.
6. Remove racks and disconnect water diverters inside the tub.
7. remove phillips head screws that hold dish washer to counter.
8, Pull out DW and lay on its side to expose bottom of dishwasher. disconnect the motor terminal plug. and disconnect the temp prope.
9. disconnect the drainage tube and then proceed to remove the 3 plastic clips that hold the pump housing to the tub.
10. I used some silcone grease around the new pump housing to be safe. then I installed the new pump housing and motor in the reverse order.

It probally took me about an hour start to finish, the hardest part was placing new housing back in. The ring around the bottom of tub is very sharp!
Left some blood there.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

My husband pulled out the dishwasher and removed the faulty part and installed the new one. We found info on the parts source website to assist us. Dishwasher works great!!! Someone from the company we purchased it from had replaced it several years ago, and the seal at the bottom had leaked and the motor had siezed because of the water. We also discoved that the water line was severly kinked in 2 places, so we installed a flexable hose. Now my dishwasher is quiet, fills much faster and all this for a fraction of the price of a new appliance. Would recommend this website.

Pulled out dishwasher. Took out old screws. Unsnapped end of rack slid new wheel in and attached to side. Very Very easy. It was great to get the part so fast and take care of this repair ourselves.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

First I removed the screws holding the outside door panel to the inside door panel. Next (at this was the tricky part) was separating the panels. In our model of dishwasher, there is a layer of Styrofoam between the two panel to reduce noise. Unfortunately the Styrofoam is glued to both panels. Separating it without damage was not possible. So it was done with brute force and the Styrofoam broke in several places.

Replacing the dispenser involved removing six screws, disconnecting the wires and popping the dispenser out. The new one went in easily although there seemed to be a correct amount of tightening to do. It was tricky to get the cover back on because the Styrofoam pieces had to go back together like a puzzle.

Once reassembled, I ran the machine and it leaked at the dispenser. So the cover came back off. This time I played with the adjustment of the dispenser, testing it with the outside cover off, to insure that I had a tight, non-leaking seal. Once done, I put the cover back on and we are back in business.

The new dispensers do not have connections for the "Add Rinse Aid" light. They use a visual indicator on the dispenser itself. I simply taped the wire for the indicator light up and left it inside the door.

One last note, on our unit, the outside door panel is two pieces. I needed only to removed the lower portion for this repair. Unfortunately, I removed both and in the process broke the small plastic end on the door latch requiring me to purchase a new one. Bummer. That was a 10 minute repair though.

I removed the dishwasher from under the cabinet. This is what took the most time. Before removing the dishwasher from under the cabinet I disconnected the drain cable to remove all the water from unit. After removing the dishwasher I tipped the unit on its left side. The motor/pump assembly is held in with one screw. After removing this screw the pump/motor assembly comes out with a 1/8 turn counter clock wise. The replacement pump/motor assembly was put back in in reverse order. After the pump/motor assembly was replaced I replaced the door balance cable kit on the right side of the unit. Next I tipped the unit on to its right side and replace the left balance cable kit. After this all that was left was to return the unit back under the cabinet and hook up the water supply line, the drain line, and the power.

I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.

Replaced pump and motor. For the price of the products individually, it only made sense to do the whole thing. As someone else mentioned, much easier to remove the dishwasher and turn it on it's side to remove/replace. Disconnect 3 fittings, 3 stop devices and remove. Other than getting about 20 cuts on my hands from all the metal, it wasn't bad at all.

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Removed leads from fuse and installed jumper wire (while the power was off, then turned back on) to determine that circuit board was still good. Ordered new fuse and installed using existing wire connections. Did not splice in new connectors that came with fuse. Wires were clean and good and did not want to cut and splice.