66513743K601 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from PITTSBURGH, PA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Unwanted water.
A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jm from OSHKOSH, WI
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Friction sleeve had torn, resulting in dishwasher door 'falling' when opening.
I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Hudson, OH
- Parts Used:
- W10542314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher leaked
Our Kitchenaid dishwasher was leaking so I called a repair service. I gave the model number and serial number over the phone and explained the problem. I was told the rubber gasket would need to be replaced. When the repairman came 5 days later he told me that the gasket needed to be replaced but he didn't have a new one on his truck. He ordered one and said he would be back in a week to repair the dishwasher. That took 10 minutes at the most. He then gave me a bill for $200.49 ($71.49 for the part and $129 for the labor)that I had to pay right then. I wrote him a check so he would leave and immediately called the repair company to tell them the price was outrageous and that I had never before paid for a repair before the work was done. I was simply told it was their policy. I then told them I was stopping payment on the check - which I did. I checked on-line for the part and found your web-site and the the part I needed for $27.62. I ordered it on a Monday, it arrived on Tuesday and my husband easily installed it that evening. Thank you, thank you, thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Bend, OR
- Parts Used:
- WP8269209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher. Quit mid-cycle.
Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Rockville, MD
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cap of a vertical tine in the dishwasher had come off, leaving an exposed, rusted and sharp top.
The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winona from Rockford, MI
- Parts Used:
- 8193983
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spinner flew off and melted.
I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conelis from Eclectic, AL
- Parts Used:
- WPW10757217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The motor was too loud
I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Las Vegas, NV
- Parts Used:
- W10301577
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
change front panel
easy as long as you have the right tool to take the panel off, maybe they could include one for people who don't have a good selection of tools. Thankfully we did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lisa from columbus, NE
- Parts Used:
- WPW10757217
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
front seal on the old pump failed causing the front bearing to get wet repeatedly and fail
Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Lebanon, CT
- Parts Used:
- W10518394, WPW10477552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher wouldn't work
Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Corona, CA
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Power Was Completely Of The Dishwasher.
I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from BILLINGS, MT
- Parts Used:
- W10727426
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from HIGGINSVILLE, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Mounting bracket
Removed old part and replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from SARATOGA SPGS, UT
- Parts Used:
- 8193983
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The Spinner at the top of the dishwasher came off and would not stay on.
First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from GRANDVIEW, MO
- Parts Used:
- W10648041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
washer filled in when off..
replaced the valve
Was this instruction helpful to you?
Thank you for voting!