58714432201 Kenmore Dishwasher - Instructions

First i removed the screws on the back panel, unscrewed the latch, removed the wires and installed the new latch.
I found the latch is too expensive for a little plastic part.

removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.

First, I located the dishwasher switch in the circuit breaker and turned it off, so as to kill power to the dishwasher - DO NOT PROCEED WITHOUT DOING THIS FIRST. Unscrewed front panel by removing 6 screws on the inside of the door frame. Then pulled 2 white wires on left and 2 black wires on right off of bottom of latch. Then used hex wrench to remove 2 hex screws holding handle and latch to frame. Then reassembled in reverse order as I disassembled. Note that there was a video on the site when I ordered the part, and it demonstrated all the steps; however, when I received the part and went back to the site to review the video again, it was gone. I'm glad I paid close attention the first time I watched it as it was extremely helpful and showed me exactly how to complete the installation.

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

Received the part quickly and installed it with no problem whatsoever. Have order parts from PartSelect before and have been very happy

I clipped the wheels onto the rack. It couldn't be any easier. then i removed the # 25 torx screw which attached the broken slide wheel to the tub and installed the new wheel with the same torx screw.

First dissconnect power, and remove the 6 phillips-head screws from the back/upper side of the door, next remove the 2 torx screws holding the handle assembly, and unplug the 2 micro switches attached to the handle. Reverse this procedure and you're finished. It's so easy, a caveman could do it.

Important - turned the power to the dishwasher off. took the screws out of the top part of the back door panel. pulled the wire leads of the broken switch, replaced the switch with the new one, reconnected the wires, put the panel back on.
Fixed

It was a walk in the park. Unscrew the six screws in the back of the panel to reach the latch. Unscrew the two torx screws in the front of the latch and replace each of the cables, one by one, in the new latch in the same order. Put the screws back into place in reverse order and... voila, wthout a single shock !!

Simple- Disconnect electric to washer, Remove inner door panel with philips screw driver, disconnect electrical wires watching exactly how they are to be replaced. remove star screws securing handle mechanism. Replace with new handle, connect wiring, replace inner door panel and your all set. Good luck.

Removed the screws that held the cover on, then removed the 2 screws that held the door latch in place. Disconnected the broken door latch and attached the new one. Put all the screws back in and that was it! Also, the shipment of the part was SO QUICK!

I opened the control knob panel. The latch assembly is located behind inside the panel along w/ the wires. This is my second replacement of the assembly. The last one lasted about 2 years. They should make a sturdier latch assembly next time.

Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

Shut the power and water off. Undid water inlet an outlet connections and unplugged power to the valve. Installed new inlet valve in reverse order and it's like having a brand new diahwasher and I saved myself neaerly $500.