58714432201 Kenmore Dishwasher - Instructions

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

removed 6 screws to take off door cover . Found two star head screws holding door latch removed them . Undid 4 wires attached to the old latch one at a time and attached in same order to new latch. I put the two star headed screws back in. secured door cover and every thing worked great.

Replacement was simple.

first of all, my name is virginia , I ordered the part for my husband and because of his work schedule I decided to try to fix it myself. It was very easy, about 8 screws and it was out and the new one was in and working. see, girls can do repairs ourselves.

Removed front cover. No instructions so I removed all the screws. Only the bottom 2 need to be removed(1 on each side) then push cover up to unlatch. Remove 2 wires and 6 screws. Replace soap dish unit. reinstall screws and wires. Replace front cover. The hardest part is the front cover.

At first I wasn't sure; I thought I had to buy the inner panel of the door. Considering that I have to minimize expenses I made it a point to tackle the problem myself. I unscrewed the outter panel off the dishwasher door and located the dispenser from inside of the inner door panel.

I unplugged the old dispenser,which was damaged, unscrewed it from the panel and removed it. I cleaned any and all debris, dirt and soap scum it had accumilated over the short years we've owned it.

Finally; after I prepared the new dispenser for installation, I placed it in position screwed it in and plugged it in, which was slightly tricky because it is pretty snug against the inside door panel. Once installed, I got my older son, 15, to help me screw in the outside panel of the door, and as he held it I screwed it on the the inside panel.

I tested it with no dishes inside by pouring just a little detergent in the new dispenser, starting the dishwasher and I stuck around in case there were any leaks or any other possible disaster that could occur.

This was exactly one week ago and all is still well. By the way, the person who took my order, I believe her name was Joann, was great. She talked to me making certain I had the right part, which I was unsure of since the diagram on your site was not quite clear. On top of that; I didn't pay for overnight service, yet my part was at my door the next day. I was amazed at the quick service and delivery. Thanks Joann!!!

Felipe,
Poughkeepsie, NY

Six screws, two torque drive screws and, four wires.
Then reverse to install. Pull out old seal wash out groove find center mark on new seal and install be sure and fold notch on bottoms. Easy

Unscrewed the screws on the door, opened it. Swapped out the latch. Screwed the door back together - GOOD AS NEW!

First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.

Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.

Removed the broken part and disconnected the four wires. Installed new part (two hex head fasteners) attached wires - good to go!
Quick delivery on the part allowed for dishwasher to be down for only a few days after the part was ordered.

I just had to buy a new cap and screw it in.

The repair was relatively easy and I probably saved enough money as to not have to buy another dishwasher. The part alone was $42. A service call and installation would have made it not cost effective to fix.
The control panel is loosened with phillips head screws on the inside of the door. The latch is attached with the "star" shaped screws. I did not own one of these drivers so I had to leave the house to get one. I used pliers to disconncet the clips from their connections as to not pull the wires from the clips.

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

Simply unscrewed the old. Replaced with the new.