58715232900A Kenmore Dishwasher - Instructions

My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!

Disconnected power, water, and drain tube from dishwasher. Pulled dishwasher out and laid it on right side. It was not necessary to remove the pump motor. When disconnecting the water line, it is better to remove 3/8 line from the appliance adapter rather that the appliance adapter from the dishwasher as the nylon connection tends to strip.

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Internet search found high limit switch as primary failure, removed dishwasher existing part looked new, no signs of wear as was expected. Second failure was the heating element, I ordered the part; At the same time I found a random youtube video, that had me check the continuity of the heater and tested good. Then the video indicated the heater relay may have one leg that has lost the solder and stops the heater element from working. I took the control panel a part and the heater relay had the same failure, one leg had a missing solder joint. Using some flux, solder and soldering iron I repaired the connection and added some addition solder to the circuit. Reassembled and the dishwasher is heating as it was before everything is working as expected!
(P.S. The heater relay failure appears to be a common problem, but the actual root cause [relay failure due to poor solder joint] is never reported back to the company, they just hear the heater element stopped working and they never fix the real issue because the customers are throwing out the dishwasher, when it could have been repaired with a simple fix. More importantly it should be something that is investigated as it may needs an engineering redesign. but can't fix what you don't know about or fail to investigate. I did purchase a new relay to replace the existing one, to be installed upon arrival).
Once again a random youtube video identifies and resolves a problem, that would have had me purchasing a new dishwasher, and maybe this is all planned engineering obsolescence.
When will get smart dishwasher that have sensors or at least codes that report the failures correctly, to make DIY repairs?

I watched the partselectrepair videos for tub gasket, bottom gasket, and splash shield. The instructions were very clear and easy to follow, thank you so much now I have a dishwasher that's good as new.

It only took about 20 minutes to replace. Thanks for the video.

I removed the kick panel at the bottom front of the dishwasher. Then using a flashlight and a cross point screwdriver, I removed the thermostat from about the middle left. It requires a short screwdriver, but not quite as short as a stubby. I unplugged the wires, noting that one of them was a little burnt looking. The burnt looking connector was still okay. I then installed the new one, with the green dot on the thermostat having the slightly burnt looking connector. Then I ran a load of dishes and the dishwasher worked as it was supposed to. It has worked okay twice since then.

Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.

Turned power off , shut the water off to washer , unhook water line , unhook drain line from sink drain , unplugged electric chord from the wall . Open the door look where the door latches you'll see two metal strap' s that are screwed under the counter . Take the screws out . Take the bottom basket out .Take the spray bar off . There's two clips on the bar just push them out lift bar up .There in the middle of the washer you'll see filter screen. There's a small handle looking thing do not know what they call it .lol Twist one way or the other to take it off . Once you have that out of the way take the three screws out mine were hecksscrews .Pull the cover off remove the ball . Take a rag and take the excise water out in the bottom . Pull the washer completely out from under the counter . Lay it on the back side on the floor . You'll see the pump it has U shape metal holding it with two screws . Take the to screws out remove the U shape metal bracket . Unplug wire going to motor squeeze the clip and pull . Twist motor back and fourth and pull slightly till it comes out . Put new O rings on new motor and lubricate O rings and slide motor back in . Reverse the process . Take pictures if you need to as your taking things off if your afraid you won't remember.

1 Removed 2 screws to remove door panel so as to access back of dispenser.
2 Unplugged 2 color-coded wires attached to dispenser
3 Removed 6 screws attaching the dispenser.

Reversed these 3 steps to install new unit.

Easy. Don't even think of calling the repairman.

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.