66513793K603 Kenmore Dishwasher - Instructions

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!

put new hose on, very easy.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

Snapped the new stops on. It took about 2 minutes.

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

I removed the upper dishwasher rack and disassembled the middle spray arm as described in other posts. Replacement was easy. The difficult part was to figure out what was causing my dishwasher to leak. I had seen many references on line to leaks being caused by the door seal or lower vent wear. I had replaced both. Those replacements resulted in less leaking, but I still had water coming out. There were also references to leaks sometimes being caused when the lower spray arm was cracked, but mine was fine. (My dishwasher has an aluminum lower arm, so it wouldn't crack.) I discovered the middle spray arm was cracked when replacing the upper dish rack. (It was starting to rust.) Apparently, when the middle spray arm is cracked, the heavier circular water flow from it creates a wave motion (vortex) in the bottom of the dishwasher. That pushes water past the seals at the bottom of the door. Once I replaced the middle spray arm the water leak problem disappeared. As an added bonus, my glasses came out cleaner! I have never seen a post indicating that a cracked middle spray arm could lead to water leakage, so hopefully this post solves someone else's mystery problem!

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

removed rack
removed one screw
removed old seal
installed new seal
installed screw

One Spring and both Balance Link Kits were broken. The repair itself was incredible easy, especially after watching the repair videos. Maybe 2 minutes per side. The moderately difficult part was removing the water supply and drain lines. Our dishwasher is some distance away from the kitchen sink. The supply and drain lines are routed behind and through some lower cabinets making reconnection a bear. Finally used a wire coat hanger as a guide and was able to re-thread the lines through the cabinets. The dishwasher could not be removed from its cabinet without first removing these lines.

I followed an excellent video on youtube which shows how to do it step by step: Dishwasher Dispenser Assembly (part #WPW10605015) - How To Replace

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

I first went on line to the KitchenAid repair web site and found my problem listed and instructions given . This first of all led me to a parts drawing for my model and then to the site connection to order the parts and receive the instructions. The parts arrived quickly and the instructions were thorough and easy to follow. This was a good experience for me.