58715219900 Kenmore Dishwasher - Instructions

Disconnected power, water, and drain tube from dishwasher. Pulled dishwasher out and laid it on right side. It was not necessary to remove the pump motor. When disconnecting the water line, it is better to remove 3/8 line from the appliance adapter rather that the appliance adapter from the dishwasher as the nylon connection tends to strip.

Internet search found high limit switch as primary failure, removed dishwasher existing part looked new, no signs of wear as was expected. Second failure was the heating element, I ordered the part; At the same time I found a random youtube video, that had me check the continuity of the heater and tested good. Then the video indicated the heater relay may have one leg that has lost the solder and stops the heater element from working. I took the control panel a part and the heater relay had the same failure, one leg had a missing solder joint. Using some flux, solder and soldering iron I repaired the connection and added some addition solder to the circuit. Reassembled and the dishwasher is heating as it was before everything is working as expected!
(P.S. The heater relay failure appears to be a common problem, but the actual root cause [relay failure due to poor solder joint] is never reported back to the company, they just hear the heater element stopped working and they never fix the real issue because the customers are throwing out the dishwasher, when it could have been repaired with a simple fix. More importantly it should be something that is investigated as it may needs an engineering redesign. but can't fix what you don't know about or fail to investigate. I did purchase a new relay to replace the existing one, to be installed upon arrival).
Once again a random youtube video identifies and resolves a problem, that would have had me purchasing a new dishwasher, and maybe this is all planned engineering obsolescence.
When will get smart dishwasher that have sensors or at least codes that report the failures correctly, to make DIY repairs?

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Watched your video repair was easy.

Figuring the issue was the Control Board, I ordered one. ($90) When it came I installed it...SAME problem. So I took it out and reinstalled the old board and it WORKS. Apparently some connection was not right and just moving the conectors by taking them in and back out twice fixed the problem. And FYI, since it is an electric part it is NOT returnable once it s been installed!

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

I ordered the wrong part ( lower arm ) it came the next day. I than ordered the right part ( middle arm ) again next day. I decided to change both ,they just popped in. The dishwasher works like new. Great people great service.

Easy

I removed the screws from the inside of the door. There are also tiny screws you have to remove that holds the part onto the door. Then I was able to remove the part, unplug the power receptacles and install the new part. Very simple!!

Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy

I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

It only took about 20 minutes to replace. Thanks for the video.