66513183K800 Kenmore Dishwasher - Instructions

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

Take out 6 screws from inside door upper most screws to control panel, removed water safety shield 3 easy tabs to release, found old fuse removed , cut wire 1 inch from old fuse removed have to pull fuse out of its plastic holder put in new fuse matched up wires, they are color coordinated, black with white stripe, and one solid black striped wires and twisted them tight, and inserted them in new wire harness that came from parts select tighten them tide them all together and used black electrical tape on all the new connections put back together and it totally fixed the problem so happy saved alot of money not having to call a service repairman

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

I followed another story for the same repair. Worked great.

Partselect provided me with tracking information for my order, they also provided an installation video. So when I replaced the door seal it was a few minutes to remove the old seal and about five minutes to put in the new one and it was all done.Thanks to Parts select it was a piece a cake

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

The old filter simply unscrews and the new one screws in.

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.

After doing some research on the Kitchen Aid issues. I turned off the breaker. Remove the (6) #15 Torx bit screws from the inside upper panel and removed the outside control panel. I located the Bi-Metal Fuse. I turned the breaker back on.Took a Electric Meter and it showed power only on one side. I order the part (BI-Metal Fuse) from the company. Turned the breaker off to there dishwasher. Very easy to install. I cut and trim the (2) wires. Match the black wire with the white stripe to the exact same color code and do the same for the all black wire. Install one wire at a time and tighten down with a small pocket screw driver. Then use the plastic tie straps to secure the (Bi-Metal Fuse).Turn the breaker back on. You are good to go.

1. Cut power to dishwasher
2. Cut water to dishwasher
3. Remove two screws that secure panel under door
4. Remove door and insulation behind it
5. Inlet valve assembly is located just behind panel on the left side
6. With your hand, press the tab on the green terminal that holds the wire harness.
7. Disconnect the harness and make sure you watch where it goes when you let go of it.
8. Unscrew the single screw that holds the inlet valve assembly to the frame.
9. With this screw out, you should be able to rotate the valve assembly around to get at the bits you need to disconnect.
10. Using pliers, slide the hose clamp up the black hose.
11. Put down a rag or paper towel because the next step involves water.
12. Carefully rotate the black hose back and forth while pulling on it to slide it off over the barbed nozzle. Probably this will take both hands. Some water will come out of the hose when you get it off.
13. Remove the incoming water supply hose from the brass fitting at the bottom of the assembly. The nature of the connection will vary. For my dishwasher, there was a brass elbow fitting I had to disconnect and then re-use with the new valve. Most likely you'll need a hex wrench and/or adjustable wrench. I had to place the disconnected valve assembly in a vise to get the elbow fitting off.
14. Discard the old valve assembly and begin attaching parts to the new one.
15. Connect the incoming water supply. When attaching the incoming water hose to the brass fitting, use a pipe thread sealant such as Tru-Blu.
16. Connect the black hose to the barbed nozzle and put the hose clamp back in position. It may be helpful to apply a dab of dish soap or food-grade synthetic grease to the nozzle to help slide the hose on.
17. Mount the valve assembly to the dishwasher frame using the existing screw.
18. Reconnect the wire harness.
19. Before you replace the panel under the door, go ahead and turn the water supply and electric power back on.
20. Turn the dishwasher on with nothing in it.
21. Inspect the area around the valve assembly to be sure it isn't leaking.
22. Once you're sure there are no leaks, turn the dishwasher off and cut electrical power again.
23. Reinstall the kick panel and insulation. You may need to spend some time adjusting its position to get the screw holes to line up.
24. Turn power back on and enjoy your dishwasher.

Once I figured it out it was not bad at all and most of all it worked, no leaks. I just cleaned some old glue off the stainless steel, dried it well, ran a bead of glue like directions showed, squeezed in the new gasket, closed the door for 24 hours then ran the dishwasher. No Problems.

I went on line and saw a video mentioning it may be the fuse and in order to verify that, take piece of scrap wire and jump pass the fuse.If the lights come on then its the fuse,I did and it was.So I found your web site, typed in the word fuse and the part number came up w/ your video showing how to install it. It was GREAT and what a great idea too having the video available w/ the part! I killed the power and I unscrewed the screws and placed them in the pattern they came out of because some are longer than others. I supported the front cover with my knee and had found the wires in advance so I knew which ones to cut, strip and screw into the new replacement part.I replaced it back in the snap on fuse holder and re-screwed it back together starting with the latch ones, using a criss cross pattern like on a tire. And that was that...I will DEFINITELY use this site again...........hopefully not for a while! Thanks so much.