58714019402 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- william from spring, TX
- Parts Used:
- 5304535380
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top rack wheels on rack got eat up from dishwasher pods. Cheap made junk made in mexico. make nothing good no more.
Looseing up rack wheeles took out keepers slid in new rack put in keepers and tighten wheel nuts make sure there tight thats it easy a baby can do it.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was making screeching sound.
Disconnected the water line. Pulled the dishwasher out from underneath the counter. Turned the dishwasher on its side. Removed the two screws that were holding the motor in place with a special screwdriver set I had to buy. Removed the motor. Found that the front O-ring on the motor was mangled. Replaced the O-ring. No more screeching. The dishwasher now cleans the dishes better than the day I first bought it. I have to wonder if that O-ring was ever installed properly from the factory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray D from LAWRENCEBURG, TN
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Leak at door
As shown on you tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sacramento, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket leak
First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.
Was this instruction helpful to you?
Thank you for voting!
Door leaked in corner
Pull the old parts out put new ones in..Changed bottom door seal and door tub gasket. In about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert e from HOPATCONG, NJ
- Parts Used:
- 154430501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken door spring on dishwasher
used pliers to hook up spring according to repair video.5 mins to check for proper tension.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MIDDLETON, ID
- Parts Used:
- A00104102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
a part of the latch broke off causing the latch to not secure the door
on a U-TUBE repair sequence it showed removing the entire front panel of the door. With this Kenmore model the front panel is in two parts. The upper part where the controls and latch are is independent of the front panel so all I needed was to unscrew the upper panel, unscrew the latch, pull off the wires and reinstall by plugging in the wires, screwing the new latch to the door, reinstalling the panel to the door. It took about 15-20 minutes for the entire operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Summerville, SC
- Parts Used:
- 154388801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rinse cap was mutilated, the rinse agent leaked.
Simply unscrewed the old. Replaced with the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from LOVINGTON, NM
- Parts Used:
- 5304509753
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
No problems encountered
There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.
Was this instruction helpful to you?
Thank you for voting!
Door won't stay up and door leaking on floor
Replacing the door bottom gasket is a breeze, just grasp with a needle nose pliers and pull out. I positioned a small mirror inside the dishwasher so I could see where the gasket fit back in. I pushed the new gasket into the slot and ----done.
The springs require that the dishwasher be pulled out from its opening after removing the screws holding it into the cabinet at the top of the dishwasher. Replacing the springs is easy, just remove the old ones from the the bottom frame holes and the plastic holder and put the new ones on through the plastic holder and then into the frame. Push the dishwasher back into its opening, square it with the cabinet and reinstall the mounting screws.
The springs require that the dishwasher be pulled out from its opening after removing the screws holding it into the cabinet at the top of the dishwasher. Replacing the springs is easy, just remove the old ones from the the bottom frame holes and the plastic holder and put the new ones on through the plastic holder and then into the frame. Push the dishwasher back into its opening, square it with the cabinet and reinstall the mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Oak Creek, WI
- Parts Used:
- A00104102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch was busted
cannot describe because not good at it however I just read what everyone else did and it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Stafford, VA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Relay shorted out after diagnostics ran
Removed two screws on each side, lower half. Inside, removed six screws. Replaced the assembly and replaced all screws.
Not worth the fifty dollars for the part, just to have a door open at the right time to empty soap. Quite a hefty price to pay considering the price of the machine
Not worth the fifty dollars for the part, just to have a door open at the right time to empty soap. Quite a hefty price to pay considering the price of the machine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Lebanon, MO
- Parts Used:
- A00126501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher wouldnt drain
I removed the drain hose from the drain pump removed 2 screws then removed smaller drain hose and disconnected 2 wires. The new drain pump was now ready to put in. Very easy job! Customer service made ordering the pump very easy!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Milwaukee, WI
- Parts Used:
- A00126501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
drain pump no longer worked
removed the old pump and replaced it with a new one
Was this instruction helpful to you?
Thank you for voting!