58716109801 Kenmore Dishwasher - Instructions

FRIDGEADAIRE - GALAXY SERIES -Part arrived within 3 days of order BUT it was wrong part. All excited about getting the upper wash rack in full operation once again. Pilled shelf out to remove gasket to find it looked nothing like the one on there. The part I need is like a bellows of sorts that fits on the water line attached to the upper shelf. The part received goes on the back wall.
Now i am back at square one with part I don't need and hoping for the part I do need

Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

The unit would not pump the gray water out so I immediately assumed it was a bad pump. Ordered the part and had it the next day. After taking things apart I realized it was a clogged discharge hose and the original pump was still good. Since I had the new pump and everything was already disassembled I decided it would be a good insurance policy to replace the pump anyways. Easy to install. I didn't even have to pull the unit out. Just did it from underneath.

First disconnect the power. Open the dishwasher door. Unscrew all of the screws except the top two screws. Unscrew the top two screws last and slide the door off. Unscrew the housing for the control board. Disconnect the wires from the control board(take a picture or mental note where the wires are positioned for reinstalling). Unscrew the control board. Put the new board in and go in reverse order until the job is complete. Good luck.

First I removed the six Phillips head screws that hold the control panel on. Next I removed the two Phillips screws holding the door latch in place. Then attached the new latch and reversed the procedure. Best part was the prompt delivery of the new part. My wife had herself convinced she would be without her dishwasher for several days.

Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.

Replaced the entire top rack with spray bar.

Removed old spray arm, fitted new spray arm. VEry easy. Sorry I didn't do it months ago

I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).

I closed on a house a few weeks back. You really don't notice issues with appliances until your living there....the walk through doesn't give you the time to really see anything hidden. Anyway - the dishwasher had appeared to be used to wash grease covered parts from a car so I pulled all the racks and filters out and placed the order for replacement parts. I saved hundreds in obtaining replacement parts verse buying a new machine - and I didn't have to sit around waiting for a repairman to do the work for me. I've made several purchases from PartSelect, and will probably making more in the near futre - Thanks!

First I removed the bottom dish rack to gain access to the spray arm. I proceeded by pulling straight up on the bottom spray arm, it disconnected with gentle force. The replacement part was not identical, so I determined that it would work by inspecting hole patterns and heat shield configuration. Then I gently pushed the new spray arm onto the water supply tube making sure that the spray arm snapped into place. Due to extremely fast ground shipping (less than 20hrs from order to my door) the repair was done within 24 hrs! Boy...was my wife pleased!

Removed screws and put new bottom gasket in old one just fell out.

took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .

I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the door, facing inside. The bottom screw on each side. Thanks for all the help.