66513483K903 Kenmore Dishwasher - Instructions

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

put new hose on, very easy.

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

Be sure to shut off power at circuit breaker and disconnect drain and water supply. Remove the dishwasher from the cabinet, lower it on its side. Remove three electrical connections from motor to various sensors. Remove three plastic wedges that secure the motor gasket to make a tight seal. The motor pops into the body of the dishwasher for removal. The replacement motor goes in just as you took it out. It took two people to set the motor right to ensure the good seal on the gasket for re-installation. Then turn it back upright and secure it in place. Couple suggestions, be sure to have ample towels around for leakage from water and drain lines. Be sure to cover the bottom of the dishwasher during disassembly and reassembly of the wash manifold. I dropped a screw in there and it took me some time to fish it out.
All in all, it went well. Don't pay a plumber for this job. I'm a clod and if I did it, you can.

12 screws remove door outside panel unplug wire remove 6 mounting screw remove old unit put new unit in place put 6 small mounting screws back plug wire in put front door panel in place put 12 door screws in your done now you can start and test run

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

Got on line at PartSelect and provided the requested Model and Serial numbers. I also used YouTube to "armchair" diagnose the symptoms and reviewed several suggested fixes. Our "touch panel" containing all the control buttons had deteriorated over the years, and I speculated that this panel could be the problem. Since the dishwasher is a few years old and has had heavy use, I also assumed that the thermal sensor would be bad, or at least at the end of its life. Since one LED on the control panel still worked, I knew the unit had power going through it. So I removed the upper latching mechanism and touch panel screws and pulled the panel apart to inspect it for signs of burning, corrosion and possible deterioration. The electronics looked good so I cut the power at my main household electrical panel and proceeded to disassemble and unsnap the inside covers. Then I disconnected two electrical connectors and carefully unfastened the electronics ribbon. I snipped two wires leading to the thermal fuse, replaced them with a new sensor (spliced the two wire feeders with electric nuts) and put that back in place. Then I snapped the new touch control panel back together, replaced the protective cover, and the screws I had removed. I re-energized the house electric panel and-- WALA --the dishwasher sprung back to life! I'm probably slow and methodical, but it took me about 30 minutes to disassemble and reassemble the unit with the new parts. It's great to have the machine back in service, and the tab was only about $160.

I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.