665KUDS23HB0 Kenmore Dishwasher - Instructions

The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.

Used a heat gun (or hair dryer could probably work)to stretch the ends of the hose to slip over areas to connect.

Our old Kitchenaid Dishwasher was not getting the glasses on the top shelf clean. I looked and found the tube running to the washer arm under the top basket was split.
I replaced the tube. First I put dish soap in the ends of the new tube, so they slipped onto the other parts with only moderate force.
Now the dishwasher is making the glasses in the top basket clean again.
Regards,
Bob

I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.

Replaced the tube. It was relatively easy although it did take a small bit of squeezing/reshaping the newer rubber tubing to get it to fit on the outlet (it was a bit snug.)

Took the old one off then used canola oil to put on the inside of the tube and it went on easy.

One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.

I pulled out the old hose and pushed in the new one. Took a little muscle, but was glad that it fit. On line site very helpful with description so that it fit perfectly!

Simply popped on new axles and wheels and dishwasher works like new!

it was a very easy repair thank you

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

Removed the old part. It came out with no problem
due to being brittle and cracked. This part was original to my 15 1/2 year old dishwasher.

Ran hot tap water in the sink and soaked the new "Rubber Water Delivery Tube" for about 5 min. I put a little dish washing liquid on dishwasher part where tube was to be slid onto. Including the soaking time,repair took less than 5 1/2 min.

I'm very pleased by the fact that my part arrived in a little over 1 1/2 days.

Was lucky the part was available. I put liquid detergent on both ends of tube, then slid each end onto each sleeve. Works great now!

I removed the old tube. I rubbed vegetable oil on the inside of both ends. The new tube slipped on with no
problem, and that was the end of the repair.