66515825691 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- mike from SHELTON, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Preston from Atlanta, GA
- Parts Used:
- WP3369193
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The access panel below the dishwasher had broken loose from the upper screws.
The panel was removed by removing the lower screws and lifting the panel out. The old panel had a wood insert to match the cabinets in the kitchen. I removed the upper plastic piece holding the wood in place and slipped it out. I inserted this into the new access panel and attached the upper plastic piece to hold it in place. I detached the metal vent piece from the bottom of the old access panel and snapped it into the new panel. I then slipped the metal vent over the lower screws and tightened them. Finally I inserted the upper screws and tightened the panel into place. It took less time than I expected and only required a nut driver and a screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lock Haven, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from encinitas, CA
- Parts Used:
- WP3376846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer arm wound rotate, bearing was worn.
required NO tools,
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Henderson, KY
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Middletown, MD
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.
Just removed the old lower dishrack and set in the new one. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Hicksville, NY
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishrack was rusted and chipped
Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Althea from Vancouver, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from New Carlisle, OH
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
poor water circulation
follow instructions, unscrew old part, screw in new part, worked like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from New Freedom, PA
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty Dishes
Nozzle cap rubber housing was split and cracked. It simply unscrews. The replacement was a matter of screwing the new nozzle cap on. My wife was trusted with this installation. Believe me, this indicates how easy it was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from TEMECULA, CA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
NEW GASKET
I USED A PLUMBER
Was this instruction helpful to you?
Thank you for voting!