58714002991 Kenmore Dishwasher - Instructions

I removed the door panel and ran the dishwasher to determine where it was leaking. Ordered the parts. When parts arrived I removed door in order to get at the bottom door gasket, replace it, and removed the tube gasket and replaced it with new parts. The whole job was very easy for a person that's never repaired a dishwasher before. I also found that the return tube gasket at the top of the dishwasher was leaking and repaired that by making a new gasket out of a flat piece of rubber and an o-ring. All leaks have been repaired. With regards to the return tube issue, it may have only been loose and if so, I could have just tightened the return tube outlet and gotten the same results. The people at this site were excellent. Thank You

Removed 6 phillips head screws that hold the front panel in place...let the panel hang in place...then remove 2 torex screws that hold the handle to the dishwasher ( # 25 torex screw driver needed ).......then pry the wire connections off the old handle..remembering where they go on the new latch.....and reverse the process for the new handle install..and for the gasket just follow the inst's on the sheet that comes with the kit..very easy...but when you close the dishwasher with the new gasket..it's going to be very hard to close..( well for me it was )for the 1st few times...

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

I received the parts 3 working days from order. They were in perfect condition and exactly like the originals.
Pulled dishwasher out from under counter. Removed door. Replaced drain hose. Replaced gasket. Replaced springs. Put door back on. Tried rinse cycle. Placed dishwasher back under counter. Works like new.

Viewing the instruction video provided online made my repair process extremely easy. Only thing that held me up was finding a tool to help me remove the torque screws from the latch. Thank goodness for inheriting my grandfather's tools and eventually finding the right bit. The latch came with a new gasket but I recommend not replacing it if it's not necessary. I did replace ours at first but it was too thick and caused our dishwasher to leak. So I placed our original gasket back after cleaning it up and it works just fine. This wife was able to complete this project with two kids under the age of 4 and a hyper border collie running around while the husband was at work.

1. Engage B.R.A.I.N. :
B: Break open the Box. You know you'll never get it back in
R: Read Instructions: It's not more packing material.
A: Assemble New One: Put it together just like the old one
I: Ignore Instruction: Seriously, sharp edges will cut me?
N Never listen to the wife Or at least pretend to be listening

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

New piece snapped right on

Removed two screws,one on each side of the bottom part of the door. The door cover then comes off. Then 6 screws hold on the dispenser. Shut off power and remove two wire connections. Replace dispenser. Replace lower door cover and two screws. Done.

This repair project was easy enough that my 15 yr old son had it almost all done without me. The hardest part was getting the wires unplugged from the old latch. Once we got the pliers out to help us get a grip, everything went smoothly!
This was a quick and easy fix for an older dishwasher that still works!

I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.

Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.

I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.

I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.