6651761591 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Vancouver, WA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Door hinge broke
All pieces just snap off and the new one just snap right back in place.
Remeber take a little time to do your repair correctly.
It is cheaper to repair an appliance than it is to replace.
Remeber take a little time to do your repair correctly.
It is cheaper to repair an appliance than it is to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from New Freedom, PA
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty Dishes
Nozzle cap rubber housing was split and cracked. It simply unscrews. The replacement was a matter of screwing the new nozzle cap on. My wife was trusted with this installation. Believe me, this indicates how easy it was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Enderlin, ND
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking around door
After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dino from WURTSBORO, NY
- Parts Used:
- WP8274220
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water would not stop flowing into dishwasher causing it to overflow on the floor
This is a portable dishwasher.. so first I turned power off and connected water line. When I turned the water on I noticed the water would flow into the dishwasher. This is not suppose to happen. This told me it was the flow valve. I disconnected water line, turned power off and removed bottom plate, removed screw holding valve on, removed water hose and output hose and unplugged valve. Then installed new valve. Turned water on to test and water did not flow into unit until cycle started. So simple. Problem solved in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from BERKELEY LAKE, GA
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Cutter Spring was totally disfigured and pulled apart. Not functional.
Repair went exactly like the video i watched online. Perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from CLEVELAND, OH
- Parts Used:
- WP8066018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Soap door wouldn't open.
I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from WHITESBURG, KY
- Parts Used:
- WP3369769
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Remodeling a house and front panel on dishwasher was bent and needed replaced. I just measured panel and ordered without a model or part number. Was so lucky the panel fit perfect.
Just took old panel off and went side to side and then slide panel under front trim. Of course it was easier because the bottom door trim was off and now I have to find that replacement part. Not having any luck with that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from CHESTERFIELD, MO
- Parts Used:
- WP3368999
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dishwasher would not dispense soap
Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Ulysses, KS
- Parts Used:
- WPW10509257
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dish washer leaking out bottom of door
New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce W from WESTERLY, RI
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost the cap to the Rinse aid container in door
Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from VAIL, IA
- Parts Used:
- W10833650
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Coating was worn and rack was rusting and coming apart.
Polled old rack out, removed water cone from old rack with quarter counter clockwise turn. Install cone in new rack. Slide new rack in washer. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from KINGSPORT, TN
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
i had a leak under the dishwasher when the pump turned on.
I replaced the seals per the video instructions.
Was this instruction helpful to you?
Thank you for voting!