36314475791 Kenmore Dishwasher - Instructions

Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

Followed easy instructions and completed repair in less than 30 minutes.

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

My dishwasher used this part # as a substitute for the original part, which i guess is no longer made. After reading the other customers' comments,I thought people were describing two very different experiences with the installation -- some just "popped the cap off the end," or "couldn't be easier." Others had so much difficulty getting the cap off that they broke the cap. I think people must be dealing with totally different kinds of plastic caps. When I started on mine, I couldn't find a way to just "pop" the cap off. It was made so that some small flexible stems or prongs that slid in when installed could not be slid back out. I used a pliers to twist, poke, tilt, bend, whatever I could do to get the plastic cap off the end. That wasn't working, so I tried to bend rims the metal track open, but found the metal was too thick or strong for me to bend it. So I had to twist and force the cap, and the piece that kept the cap on broke off. On one side of the rack it was broken so badly that it couldn't be put back on--kept falling off. Had to try to crimp the rims of the track inward to keep the cap on. It's very loose but it has stayed in for the most part. The cap on the other side cracked enough to get it out without completely breaking off a piece. It went back in better than the first side. Pretty frustrating! I suspect because I don't have the original part with replacement caps to slide in. ?????

Held panel in place and drilled holes and installed drill screws.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

To remove the old upper rack, I needed to use a screw driver to snap out the plastic end stops. That took a little time, because my dishwasher is located in a corner of my counter/cabinets, making the stop on the right very difficult to get to. Once that was done, I just slid the old rack out, the new rack in and replaced the stoppers. I was very impressed with your service and received my order in less time than stated on my order form. Will definitely use you again and recommend you to others!

Removed old gasket, cleaned grooves, installed new gasket

Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.

The new rack was somewhat similiar, but the center section that had to be snapped on was different...no spinner on top...thank goodness for the little video on how to take the stoppers off and reinstall them...it worked...thank you for what you have provided the public and me!

The hardest part about this is removing the end caps. I had repaired the wheels a long time ago so I had some idea about how to do it. Bending the back of the end cap very slightly and twisting got them out. Then it was simply a matter of switching the racks, which came with its own wheels, and then putting the end caps back on.

I am so pleased with Parts Select. I placed my order on Sunday night and the parts were here on Tuesday morning. the install went well except for a small handful of spare parts! Anyway it looks like new and runs with no leaks.