6651765591 Kenmore Dishwasher - Instructions

put new seal in and it still leaked!hum

Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.

I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on

Remove completely the old one and installed the new entire kit.

Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.

You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.

dropped the new float in, works like a charm

The hardest part was locating the leak. After consulting the other repair suggestions, I concluded that the gasket was a little more worn on one side than the other so I ordered the gasket. The evening before the gasket arrived (quick delivery from partselect.com) I decided to shim out the old gasket with some old door insulation. It made the door harder to close but it didn't leak any more. When the gasket arrived I replaced the old with the new. It leaked more than ever. After reading more repair instructions, I decided to take apart the door vent and check it. It was packed solid with gunk. After a good cleaning, I put everything back together. No leaks! I tried every repair listed except the door vent. Guess steam is a good gunk conduit LOL. I supposed I didn't really need the new door gasket but I can tell the door has a tighter seal now. Here's a tip to watch for. If the door doesn't leak right away after the washer starts, take the door apart and look at the vent. It can look just fine from the outside and that's deceiving. Someone else mentioned the 'leak' timing that finally got my attention and lead to the 'fix.'

Watched your video

We followed the excellent video until we couldn't remove the outlet impeller because the motor shaft was not being held by the failed impeller. We drilled small holes around the impeller shaft until we could break off the upper part of the pump shell. Then we could hold the motor shaft with a vice-grip pliers by squeezing the shaft of the remaing impeller piece. We then removed the retaining screw and the rest of the impeller. Then evrything went well by following the video. There was still a bit of doubt because we discarded more old parts then expected but the machine now works well and we see no leaks.

I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!

I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!

Using a Torx screwdriver, I removed the fasteners holding the control panel/latch section of the door on the dishwasher. I tested the high limit thermostat with a multimeter. Just two terminals, one being power in, the other power out. The part had what I have heard call a "high resistance open". In other words, the power was not getting from "A" to "B". Power in - not out. After cutting power to the unit, I removed the part (just pull it out of the retaining clip and pull the terminals from the part). After receiving the part...by the way, really fast delivery...I reconnected the part (it doesn't matter which wire goes where), pushed the part back into the retaining clip, replaced and fastened the control panel, then restored power to the unit. Runs like new.