66515708890 Kenmore Dishwasher - Instructions

Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.

Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!

It was very simple, the repair took less than 5 minutes start to finish. I removed the top dish rack, took out two screws and the broken part slipped right off the water feed tube. I slipped the new upper wash assembly on the end of the tube and replaced one screw. My dishwasher is an older model and the new part only has a hole for one screw but I cannot tell any difference in stability or performance. I put the top rack back on and the dishwasher is as good as before.

used a screw driver, removed 2 screws, removed broken piece, screwed in new part ....all done :)
took less than 15 minutes to do*

i just wanted to let everyone know..I ordered the part on a monday and received it on wednesday I was amazed...the part fit perfectly ...and was very easy to install myself....ty so much ...

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

Used nut driver to remove old spray arm assembly on top rack. Reinstalled the new assembly, clamped the holding assembly onto the rack, tightened the holding assembly--that's it.

First I removed the upper basket from the dishwasher by taking off the end clips from the right and left hand slides. The clips are removed by prying them gently upward with a screwdriver.

Second I removed the old spray arm assembly by slipping the old tube off of the rotary fitting.

Third I removed the center screw from the rotary fitting which holds the upper spary arm in place. I also removed the small plastic piece (block) which is clipped to the wire basket.

Fourth I installed the new spray arm assembly making sure to orient the plastic spacer block so that the spray arm rotates freely. The spacer block clips on the wire tray and the assembly is held in place with a single screw.

The new assembly includes a one piece extension tube and end funnel so it is really easy to install.

Removed old parts, removed one screw. Then installed new kit, replaced one screw.
No problems.

Removed the top basket and replaced the spray arm kit. Put basket back in. Thanks

The hardest part was getting the clips off the brackets to release the top drawer. Was a super easy project to do myself. I'm a female and if I can do this anyone can. I watched the video that was at the bottom of the parts page when I was deciding what to order. Took less than 15 minutes to do the entire assembly. Now also the unit is all once piece from the sprayer arm to the wall. More slim lined.

I followed the illustrative that accompanied the part and bingo, it was done. The instructional video was perfect....

I watched the video for the installation which was very easy to follow. I received my part kit quickly and was able to remove the old parts and replace with the new parts. Every thing went just like the video had shown. Glasses that usually sit on the top rack came out squeaky clean now.

Got the replacement part from Part Select which had been redesigned to include the previously 3 separate parts into 1. FIRST I took a picture of how the old parts were connected up to the other parts. I thought I wouldn't need a new upper sprayer arm but I did; which was why it was included. Don't think that you have extra parts (you don't). Using a phillips screwdriver removed the old upper sprayer arm assembly. It just falls off, so be prepared to support the underside with your other hand. Also removed rear support hanger. Once off the parts just go back very easily. Just have to watch where you put the new rear support hanger so it doesn't interfere with the upper sprayer arm. Insert the new screw, give the upper sprayer arm a spin to check clearance and you're done. The thing that took me the longest was finding the phillips screwdriver. And...PS - I'm a 68 yr old Grandma

Followed the video. However, the end caps on the track were not as shown on the video and could not be removed as depicted. Broke the end caps and replaced them with thin wooden dowels.

Replace previous rack.