36314181202 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from NEW YORK, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door leakage
The instructions provided are very good if I had done before. My concern was getting the gasket to sit properly at the bottom where you cannot see. I removed the inside of the door (7 screws) and this made it easier to assure gasket sat properly in the track. may have cost an extra 15 minutes but worth it. If I do again I will take door apart again, however I think this is fixed and should not need attention again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SOUTHPORT, NC
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Terra Ceia, FL
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
The water valve went out
I took the old one off and replaced it with the new one, which fir perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from King Of Prussia, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The drain solenoid burned up
Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Canton, GA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
The pump shaft leaked
I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CARUTHERSVLLE, MO
- Parts Used:
- WD13X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would go on and off during operation
Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Rimersburg, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The dishwasher would not drain water out.
I removed 2 screws a wire plug connector and replaced the old part. The total repair including putting the cover plate back on only took about 15 minutes. Also I saved approximately $130.00 by doing this repair my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Mayetta, KS
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water not draining.
Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Rockville, MO
- Parts Used:
- WD24X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Couldn't drain water
I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from wellington, FL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Dishwasher would not drain
Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- merritt from venice, FL
- Parts Used:
- WD21X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Won't drain,Won't fill, float switch good. After installing timer it worked once. decided to replace the whole dishwasher
Remove the back of the front panel. Replace timer held by 2 screws and 2 elec. connectors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from florida, MI
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher did'nt drain water . solinoid was melted and stuck
First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Lafayette, LA
- Parts Used:
- WD27X10225, WD02X10126, WD27X10066, WD02X10054
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Panels were accidentally thrown out
The access panel fit perfectly. The screw holes lined up just right and the screws went in without any trouble. The toe kick panel was a different story. It almost seems like it is a generic, one panel fits all part. I couldn't figure out how to attach it to the dishwasher. None of the holes/slots lined up with anything, so it is just sitting there being held in place by the access panel and the floor.
Was this instruction helpful to you?
Thank you for voting!