36315655890 Kenmore Dishwasher - Instructions

Opened package, removed cap and screwed it in place.

Used drill and easy out to remove broken part, then put in new one

Recieved universal parts f/ pump & mtr assy. sorted them out, picked the ones I needed to complete my repair. Installed new assy, checked operation and was completly done in about an hour.

My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

Removed the front door panel myself... pretty easy
Removed the lower panel myself... pretty easy
Tried to put new door panel & lower panel on....
had to call the x-husband to come over & do it for me! UGH!!!! HA! He is very handy and it took him a long while. Screws are not easily accessible.
But, it looks like a new dishwasher now!!! Thanks!
The moral of this story is... if you are a women... call a man to do this job!

I pulled the two clips in the rack guides and pulled out rack and reinstalled the new rack and put the clip back in the rack guides

Thanks for your prompt shipment of the rack I ordered

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

Remove the screen that runs along the back of the dishwasher.In the middle of the area that was covered with the screen you will see a white plastic valve with 2 little ears sticking up. Use the nose of a pair of pliers to twist counter/clockwise on the valve and it will come right out. Inspect the valve.If the rubber cone shaped valve inside the valve can be pushed through the top of the valve ,the valve is bad.Replace it and go wash your dishes.

Removed the 4 1/4" screws holding the rear screen to the bottom of the inside of dishwasher. "Piston & Nut" assembly was badly corroded- to the point that no dirty water was leaving the dishwasher. Because the appliance is at least 10 yrs old and there was nothing happening during the rinse cycle, I initially assumed the worst- that the pump was bad. After reading the other descriptions of the problem here, I said, "what the hell?, if a $20 part fixes it, I'll be amazed- if not, I'm out $20 and looking at another $300 for a new dishwasher!" The $20 part (inc. shipping) did the trick. Thank you, and your website is on my "highly recommended" list! One note- the piston & nut assembly did offer some resistance as you might expect after being "gunked" in place for 10 years. However, the top has some lugs or ears built into it, so a few taps with a hammer on my largest straight-blade screwdriver loosened it right up...

Looked online for a general cause. ABout 60 to 80 percent, the cause was the piston and nut assembly located in the back of the dishwasher. Ordered the part and installed in nothing flat. Only four nut screws to remove the take the filter off and unscrew the piston and nut assembly. Next cycle, no water and the drying cycle seemed to be better. Guess because no water in the bottom of the dishwasher. Good input and fast turn around on the part.

Partselect was the only one that had the correct solution. The Piston and Nut assembly fix the problem. The washer on top of the piston was worn and it would not fully close. Replace the piston and nut assembly within 15 minutes after I found it.Shipping was supposed to be within 3 days. The part came the next business day during the thanksgiving holiday. WOW

I put on my rubber gloves, removed the lower wash rack, removed four screws from the drain guard. I unscrewed the defective part, installed the new assembly and hand tightened. Replaced the cover and installed the screws removed earlier. Re installed the lower tray, and ran the rinse and drain cycle. It has been working beautifully ever since.

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.