66515925691 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Park Ridge, NJ
- Parts Used:
- W10844024
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Bad Water Inlet Valve
No Water supply to Dishwasher. Turned off main Supply valve under sink.First took off old Diswasher supply valve and repaired it by cleaning it and it worked for two weeks. I ordered the part, but then cancelled it and Partselect service was great and cancelled it immediately. After it went down after 2 weeks I re-ordered it and it came in 4 days.
To Take this part off I removed mounting scews with nut driver, disconeected electronic plug connector, removed the compression fitting from the water supply and removed the outlet hose..reversed all of the above to install.
To Take this part off I removed mounting scews with nut driver, disconeected electronic plug connector, removed the compression fitting from the water supply and removed the outlet hose..reversed all of the above to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carla from BON AQUA, TN
- Parts Used:
- WP3378149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Latch Plate was broken
Very easy repair. I gently removed the rubber seal at the top of the tub. here I found the 2 holes to screw the new plate into place. Put the seal back over the hole and job done. Thanks for all the help from the very supportive staff. Yes, a woman did this repair. Dishwasher working like brand new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Danville, PA
- Parts Used:
- WP3376846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher wasn't cleaning the dishes
I removed the bottom spray arm and replaced the worn part. Now the arm turned freely and was performing as it was designed to do. I appreciate parts select for having the part available since the manufacturer no longer supported the model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EVELYN from GROTON, NY
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not cleaning properly
Unscrewed the nozzle cap, screwed in the new nozzle cap. What a snap! Sure beats a $75.00 service call and a parts bill that would be double what I paid!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from potomac, MD
- Parts Used:
- WP3378138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The soap dispenser lid was broken
I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl von der from HUNTINGTN BCH, CA
- Parts Used:
- W10728160
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine Row Rusted
At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.
Was this instruction helpful to you?
Thank you for voting!
SOAP DISPENSER DOOR DID NOT CLOSE.
WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Winnemucca, NV
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
dish washer leaking
Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Hollister, CA
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Part in the lower rack had rusted out
There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sherwood, OR
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
A spring was broken in the disposal chopper
I bought the kit because it had other parts that I thought I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Coolidge, AZ
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cap was missing/lost.
Easy fix. It’s a screw on by hand piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lock Haven, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from encinitas, CA
- Parts Used:
- WP3376846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer arm wound rotate, bearing was worn.
required NO tools,
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!