36314779100 Kenmore Dishwasher - Instructions

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.

Hired my neighbor, who is a plumber.

I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.

Took end caps off roller guides. Slid old out...slid new in...poped end caps back on...done. Too EASY!

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy

First of all this site is awesome. So helpful in diagnosing and ordering the part. I highly recommend!

So, the solenoid was melted and needed to be replaced. If you're looking from the front of the dishwasher it's on the left side and it has 2 screws and a c ring. I couldn't get the c ring back on, but the piece stays on without it. Works fine now.

I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!

DISCONNECT POWER TO THE DW FIRST! First of all, I need to let you know that my DIY skills usually involve calling someone else to do the job! But I found a couple of good videos online that provided some basic information about the remove/replace steps for the timer. What they DIDN'T warn me about was that there is a spring-loaded lever located directly between the timer and the dw door. When I took the timer off, the lever and spring went flying! The lever that fell off is actually a part of the soap dispenser mechanism. It took me a while (45 minutes) to figure out how all of the pieces went back together. There is a small post on the door that one end of the spring attaches to. The other end of the spring attaches to the open end of the white lever - this lever goes between the timer and the door- kind of an important step to make sure you have these pieces when putting the unit back together! As you put the cover back on the dw door, make sure that the white lever and the black soap dispenser lever are connected (you will have to spin the black lever so that it will connect with the white lever). Just make sure to take your time and breathe! This was a little frustrating at first, but if you relax and try to visualize how the pieces fit together, you'll be running dishes again in no time! Good luck!

Removed screws and replaced the part. It couldn't of been earlier. Only problem this kit didn't include a toe kick and we are having a hard time finding it.

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

I removed 2 screws a wire plug connector and replaced the old part. The total repair including putting the cover plate back on only took about 15 minutes. Also I saved approximately $130.00 by doing this repair my self.

Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...

Simply opened the dishwasher door, removed the gasket insert located in the middle inside of the door and replaced with new. Also went ahead and replaced the seal on the inner edge of the inside dishwasher door. Found very simple instructions on Google on how to do make this repair. Very easy!