6651574990 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles F. from Burnet, TX
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water leaked through door gasket.
Lowered door and put a weight on it to keep it open. with screwdriver pried out the old gasket. It was simple. looked at the end of the replacement gasket and inserted it into the track with the small hole down. Job Complete. about three minutes total time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROSE from ELVERSON, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water was leaking ou the door
pulled the old door seal off and pushed the new seal into place and it works great!
THANK YOU!
THANK YOU!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Dripping Springs, TX
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
front leak
pulled out the old gasket, aligned and pressed in the new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip D from Auburn, AL
- Parts Used:
- 4387043
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch had broken on detergent dispenser cover
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Beach, ND
- Parts Used:
- WP661566
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clean light was flashing and washer would not start
Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Keithville, LA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
leak in dishwasher
This was an easy fix. My husband took out the old gasket and put the new one in. It fit perfectly and no more leak. The part got to us really quickly too and that was nice. No more hand washing the dishes! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from matteson, IL
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
leaking
put new seal in and it still leaked!hum
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from North Grosvenordale, CT
- Parts Used:
- WP3369769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Didn't look good with the new big panel changed.
Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Las Vegas, NY
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Newnan, GA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from ickesburg, PA
- Parts Used:
- WP3368999
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Long spring broke that pulls soap cup open
Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from Columbia, TN
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bryant from melbourne, AR
- Parts Used:
- WP3376397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher was overflowing
dropped the new float in, works like a charm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karolyn from Wellington, FL
- Parts Used:
- WP304170
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Super Fast Shipping
The part arrived the next day with regular postage, outstanding service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marietta, OH
- Parts Used:
- WPW10509257
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
Leaking from bottom of door
The hardest part was locating the leak. After consulting the other repair suggestions, I concluded that the gasket was a little more worn on one side than the other so I ordered the gasket. The evening before the gasket arrived (quick delivery from partselect.com) I decided to shim out the old gasket with some old door insulation. It made the door harder to close but it didn't leak any more. When the gasket arrived I replaced the old with the new. It leaked more than ever. After reading more repair instructions, I decided to take apart the door vent and check it. It was packed solid with gunk. After a good cleaning, I put everything back together. No leaks! I tried every repair listed except the door vent. Guess steam is a good gunk conduit LOL. I supposed I didn't really need the new door gasket but I can tell the door has a tighter seal now. Here's a tip to watch for. If the door doesn't leak right away after the washer starts, take the door apart and look at the vent. It can look just fine from the outside and that's deceiving. Someone else mentioned the 'leak' timing that finally got my attention and lead to the 'fix.'
Was this instruction helpful to you?
Thank you for voting!