66515928692 Kenmore Dishwasher - Instructions

Was very easy to replace broken spring which required each end of spring to be reconnected to bracket located on the door and frame of the dishwasher. Was able to complete without moving the entire dishwasher frame.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking

New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

follow instructions, unscrew old part, screw in new part, worked like new

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

Nozzle cap rubber housing was split and cracked. It simply unscrews. The replacement was a matter of screwing the new nozzle cap on. My wife was trusted with this installation. Believe me, this indicates how easy it was.

So my dishwasher is 20 some years old. Woke up in the morning to smell burning plastic and the dishwasher never moving to the next part in the cycle. I thought it was the high limit, then the cycling thermostat(because cycling you'd think it was cycling wrong). Nope. It was working fine. I used a multimeter to test the high limit(ohm reading will be closed at room temp) and for the cycling(will be open at room temp, so use a multimeter with alligator clips and a lighter to trigger it to close). All of my existing parts were fine. So I went to the timer and tested with alligator clips, each part that connected during the timing cycle. Sure enough. On the rinse and pump water out part, the contact point wasnt connecting due to corrosion and a bent prong. So I rebent it and cleaned all the contact points. All you need to do on these old washers is pull out the timer and pull off the thin plastic "sheild" over the thing. Guess what. I have a working dishwasher after having done the impossible and fixed my timer. So for those who have a dish washer that won't advance, but you can hear your timer advancing with the clicks, this is your problem. Saved myself an unknown amount of money because they don't make my timer anymore.

As described with instructions, removed original "bearing," installed replacement, removed original spring, installed replacement springs. Not difficult.

Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.

Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.

Repair went exactly like the video i watched online. Perfect

I USED A PLUMBER