66515755791 Kenmore Dishwasher - Instructions

Very easy repair. I gently removed the rubber seal at the top of the tub. here I found the 2 holes to screw the new plate into place. Put the seal back over the hole and job done. Thanks for all the help from the very supportive staff. Yes, a woman did this repair. Dishwasher working like brand new!

The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.

Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.

Hint - Order at least 2 springs! They are not expensive.

I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.

I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.

So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.

Take care

The repair went well with the major problem being I replaced the drain hose without removing the dishwasher from it's position. Due to this I removed the drain end with out being able to see the hose and put it back on by feel. Over all I was back up and running with in 30 minutes and everything has worked very well so far.

repair was very easy did need to go to the hardware store for and adapter for the hose to water inlet valve as mine had a smaller diameter connector. Otherwise followed both videos. Needed a shopvac to remove water in the bottom of the dishwasher

Removed the washer from the cabinet, although the repair kit could have been replaced without this step. However, it still made it easier. Removed the spray arm assembly and the top cover to the motor. I had to block the motor to keep it from turning while I unscrewed part number 11. The rest was very self explanatory. The "impeller" was seized onto the motor shaft (20 years old) so I had to use a chisel to break what remained off, then clean some corrosion from the shaft. The repair kit worked and the pictorial parts diagram that came with the kit was very clear. Bottom line: "Easy peasy, lemon squeezy!" Great web site for diagnosis and parts diagrams!

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.

I bought the kit because it had other parts that I thought I needed.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

Just removed the old lower dishrack and set in the new one. Nothing to it.

It just snapped in placed. Very easy.