36314232100 Kenmore Dishwasher - Instructions

Just like the video and replaced it

I looked at your web sight and saw how to repair dishwasher.

First I opened the dishwasher and removed the lower basket. Next I removed the 4 screws that hold the food filter plate in place at the back of the tub. Then I unscrewed the Piston/Check Valve assembly counterclockwise, located at the back center of the tub, by hand. I replaced the old part with the new one and reinstalled the filter plate. I ran a rinse cycle to verify that that all of the water was purged. Finally, I reinstalled the lower basket and resumed using my dishwasher.

removed screen at back of dishwasher from the inside. Twisted piston & nut assembly out by hand and replaced with new one. Very, very simple. Dishwasher works perfectly now.

First let me say, it's so easy even a caveman can do it. I removed the water out of the bottom. Then I removed the cover in the very back of the machine with a wrench. As soon as I did that, I could see the piston. Next, I twisted the white piston out with my fingers (this was the hardest part). I could see the piston had partially disintigrated. I ordered a new one, had it delivered in a few days, and put it all back in reverse. It took minutes. Thanks to the guy that posted his story, I was able to fix mine for $18.

I Just Open Door And Put Fill Cap In And Turn That It

First I removed the bottom dishwasher rack. Using a 1/4" nutdriver I removed (4) 1/4" screws from the drain cover that is inside the dishwasher all the way in the back. This will allow you to get to the piston and nut assembly which was easily removed with no tools by simply grasping and unscrewing. Used a wash cloth to wipe "gunk" from around the threads. I then screwed the new piston and nut assembly in place. Used no tools to tighten, just "snug up" by hand. The seal on my old piston and nut assembly was 50 percent gone, not sealing at all. I guess the years had taken their toll. This solved my problem. The dishwasher washes and drains as it should. Super easy fix. Took me about 10 minutes to do the repair.

Removed filter/screen by unscrewing 2 screws with a nut driver and then unscrewed the old Piston and Nut assembly and simply screwed in the new part. Problem solved and my dishes are much cleaner and the water is draining out completely. Easy fix for this frustrating problem.

Removed filter screen with the socket set, removed the piston and nut assembly with pliers, and installed the new piston and nut assembly. Put filter screen back in with hex head screws. During the process, I opened the float regulator and cleaned it out too. Water backup problems solved.

Nut driver and philips screwdriver.

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.

Removed the 4 screws holding the filter screen assembly in the back of the tub. This exposed the Piston and Nut assembly which unscrewed fairly easily.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Followed the simple instructions to unscrew the old unit and replace with the new one. The unit was easily located on a diagram on the internet and the website instructions for removal were spot on.

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.