36315165790 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Don from Holiday Island, AR
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
motor noise.
Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Rumney, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leak
Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALFRED from OWENSBORO, KY
- Parts Used:
- WD21X10013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Dishwasher wouldn't go through its cycles
replaced the master toner relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Hughes Springs, TX
- Parts Used:
- WD28X10232
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken tower
removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristine from Arboles, CO
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
the gasket was wider than the one replaced
I had to readjust the door latch to get the door to close
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Pasadena, CA
- Parts Used:
- WD27X10223, WD31X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
replace dishwasher door pannels
I am so pleased with Parts Select. I placed my order on Sunday night and the parts were here on Tuesday morning. the install went well except for a small handful of spare parts! Anyway it looks like new and runs with no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Burlington Twp., NJ
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
leaky pump
This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merwyn from Lima, OH
- Parts Used:
- WD28X10007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tower cap broke
simply snap new one in place. I will have to say your service was fantastic. I received the new cap 2nd day. I am very pleased and would not hesitate to order something else if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loring from Cambridge, MA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket deteriorated
followed the excellent instructions accompanying the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergei from West Chester, PA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replace door gasket
Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Town of Tonawanda, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
motor fan broke
I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mimi from Philadelphia, PA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Old pump leaking
The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Alpharetta, GA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher very noisy when washing/rinsing
Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burl from Spring Valley, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Motor failure because of black power wire separation.
Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Mesa, AZ
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking gasket
Removed old gasket, cleaned grooves, installed new gasket
Was this instruction helpful to you?
Thank you for voting!