110773882 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janet from Hollister, CA
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Part in the lower rack had rusted out
There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from potomac, MD
- Parts Used:
- WP3378138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The soap dispenser lid was broken
I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Salinas, CA
- Parts Used:
- WPW10253040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The coating on the upper rack had rust coming through.
Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Winnemucca, NV
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
dish washer leaking
Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sherwood, OR
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
A spring was broken in the disposal chopper
I bought the kit because it had other parts that I thought I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Wayside, NJ
- Parts Used:
- WPW10349488, WP8268812, WP8539324, 675808
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The upper rotor mount broke off.
I screwed the rack mount to the spindle using
the extra screw I ordered. I removed the upper dishrack's front stops and slid the rack
out. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.
I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.
the extra screw I ordered. I removed the upper dishrack's front stops and slid the rack
out. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.
I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Middletown, MD
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.
Just removed the old lower dishrack and set in the new one. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
Broken mount caused dishwasher to shoot water against door, caused leaking
Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Henderson, KY
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenni G from LEHI, UT
- Parts Used:
- WP8539324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Well, to make a long story short. My husband isn't mechanically inclined. He tried to surprise me and do it himself.???
I went back to the web site to make sure I'd ordered the right part.?? looked at the diagram and then watched your little video.?? He had the part hooked opposite of what was shown. (The arm wouldn't rotate) So I turned it arround. While he was still??. It took me less that 5 min and the dishwasher is working Great.????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Hicksville, NY
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishrack was rusted and chipped
Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from La Center, WA
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original lower dish rack was falling apart.
Took out old rack, put in new one. Part arrived on time and was an exact match to the original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from encinitas, CA
- Parts Used:
- WP3376846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer arm wound rotate, bearing was worn.
required NO tools,
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lock Haven, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
Was this instruction helpful to you?
Thank you for voting!
Bearing ring missing and retainer nut broken
I put the bearing ring on the washer arm and then screwed on the retainer nut.
Easy to order the needed parts
Easy to order the needed parts
Was this instruction helpful to you?
Thank you for voting!