36314171790 Kenmore Dishwasher - Instructions

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

replaced the master toner relay.

Plastic contacts on knob broke off which caused the timer to not function. I tried to glue the pieces together but the repair was unsuccessful. I had the parts list from Kenmore and I went on line to order the part. I ordered the part on Wednesday and the part arrived on Friday. The part fit perfectly and now the dishwasher is oparating correctly. Thank you.

followed the excellent instructions accompanying the gasket.

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

Followed easy instructions and completed repair in less than 30 minutes.

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

Removed old gasket, cleaned grooves, installed new gasket

Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

This was a 45 min project. New pump was a redesign. Match your style with the instruction sheet. ( pictures are upside down) Install drain on pump. Remove wirng connectors(3) and hanger. Raemove in/out pump clamps, and remove pump. Reverse procedure( I had to bend the new hanger to fit). When I first fired it up, nothing happened for about 5 min. Then water got into the pump and it started working. Quieter, more powerful spray. Grabbed a beer.

Instead of purchasing a new dishwasher, I elected to replace the motor/pump assembly which the existing was noisy and leaking water. To start to took pictures of the existing assembly and marked the wiring connections. I read the instructions a few times until I fully understood and had the necessary parts identified. The only problem was the bracket that holds the solenoid has two holes for mounting the drain feedback bracket were not threaded. I was able to tap the holes (metric) and mount the bracket. Caution must taken not damage the solenoid coil.

Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.

I had some extra problems with my water supply line since this is an old house, but I won't dwell on that. If you have an older model like mine (probably 80's) the only trick is with the drain solenoid. The kit uses a newer style solenoid that is a little different. Without getting too technical here, let me just say that if the old solenoid has a little metal lever that is actuated when the plunger goes down do not discard it. From what I have read, the dishwasher will shut down with an error code if you don't use this part and you will also have 2 wires that are just hanging there with nothing to plug in to. You will need to use an included metal plate and screws to adapt that part to the new assembly. It takes a little mechanical aptitude, but after you figure it out it works perfectly. I did not see this mentioned in the instructions but the necessary parts were included. Replacing the pump and motor was fairly simple, and all the needed parts were included in the kit. I did remove the unit from under the counter and lay it on it's back for easy access to the pump and motor. It helps to watch some You-tube videos if you are unsure about how to do this, but make sure they are working on the brand you have. All dishwashers are NOT the same.