66517752000 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from LEONARDTOWN, MD
- Parts Used:
- WP3379383
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
broken door spring
Pulled dishwasher out from counter. Took cover off and replaced door springs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timmy from NEWNAN, GA
- Parts Used:
- WP8530929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The AIR Lock was on and could not get do anything the repair man said he cannot get the part and buy a new one dishwasher I got on. The internet and founded part select and they had the part I need and with the repair video was easy thanks partselect
I follow the video and it was easy thanks! you save me money and my old dishwasher Timmy S. GA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SUGAR LAND, TX
- Parts Used:
- WP3379369
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The upper sprayer consists of a plastic spinner attached to the top of the washer.
This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from THOMPSON, CT
- Parts Used:
- WP8268873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
lower spray arm nut
Open the dishwasher door and remove the lower dish rack.
The spray arm nut had broken off and the spray arm was wobbly.
Removed the spray arm. The threads of the nut had broken off inside the arm. I used three 1/4 inch bolts and inserted them together inside the threaded part of nut and turned counterclockwise. The threaded section came out.
Once the new nut arrived, I replaced the spray arm in the dishwasher and screwed the new nut clockwise in the center of the arm. That's it!
The spray arm nut had broken off and the spray arm was wobbly.
Removed the spray arm. The threads of the nut had broken off inside the arm. I used three 1/4 inch bolts and inserted them together inside the threaded part of nut and turned counterclockwise. The threaded section came out.
Once the new nut arrived, I replaced the spray arm in the dishwasher and screwed the new nut clockwise in the center of the arm. That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from SHELTON, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Was this instruction helpful to you?
Thank you for voting!
water coming out of the washer flooding the floor
I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.
Was this instruction helpful to you?
Thank you for voting!
Lower sprayarm broken
Note I did not have a model number just the manufacturer and name on unit. The website was still able to find the part. Impressive!
Easy installation. I recommend you also get the sprayarm seal. Be careful to insure the nut is seated securely before screwing in the nut. Highly recommend the video. Good company.
Easy installation. I recommend you also get the sprayarm seal. Be careful to insure the nut is seated securely before screwing in the nut. Highly recommend the video. Good company.
Was this instruction helpful to you?
Thank you for voting!
had to replace nut that held on the bottom sprayer and replace the water inlet tube
I had already removed the old parts so when the new parts arrived, I just attached the water inlet tube holder and put the nut on the top of the sprayer assembly and it was good to go!!!! I ordered the parts one day before 3:00 and they were delivered the next day!!!! Unbelievable service!!!! Thanks and I am a very satisfied customer!!!!
Julie Welty
Julie Welty
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Middletown, MD
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.
Just removed the old lower dishrack and set in the new one. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Henderson, KY
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
Water was leaking (gushing) out the door
Researched parts - 10 minutes - - - Ordered parts - 5 minutes - - - Waited for parts - 14 DAYS! - - - Installed parts - 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from YORK, PA
- Parts Used:
- WP8268873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Nut broke
Removed piece of nut that remained and screwed in new one by hand
Was this instruction helpful to you?
Thank you for voting!