36314031001 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from Fairfield, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The rollers on the upper rack broke
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.
guides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Huntingdon Valley, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Maumee, OH
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel broken off bottom rack
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Phenix City, AL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rear wheels were missing on the lower rack.
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Columbus, OH
- Parts Used:
- WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken upper rack roller, rack kept falling off the track
Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.
Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.
Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from The Villages, FL
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers fell off lower rack of dishwasher.
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy Baldwin from Stowe, PA
- Parts Used:
- WD35X21038, WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The stud assembly in the middle of each wheel no longer stayed inside the wheel.
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Centreville, VA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack falling off of upper slides
1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from perry hall, MD
- Parts Used:
- WD35X21038, WD12X10327, WD12X10304, WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
wheel replacement
Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs
most of the parts were for future repairs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from huntley, IL
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Dish washer is not running through cycles
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Bloomington, IN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
lower dishrack rusted
replaced rack, no repairs required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from PURCELLVILLE, VA
- Parts Used:
- WD12X10327, WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
wheels were worn out and kept falling off
popped old wheel off popped new one on
for the rack roller i took the ends off and slid old rollers off then slid new ones on.
for the rack roller i took the ends off and slid old rollers off then slid new ones on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from canton, MA
- Parts Used:
- WD28X31819, WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
roller on upper rack broken - lower rack plate holders broken
lower rack took one min. take out old slide in new
upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.
upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Cornelius, NC
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
D/W would not drain. Water standing in bottom.
It is a simple process to replace the drain solenoid on these dishwashers, having replaced several in the past few months.
After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 screws, and plugging in the wire harness.
I work on a 260 + unit property, as well as working for a property management company who rents single family homes.
PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.
After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 screws, and plugging in the wire harness.
I work on a 260 + unit property, as well as working for a property management company who rents single family homes.
PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Salinas, CA
- Parts Used:
- WD28X31818, WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Racks had rusted and needed replacement
The bottom rack was a breeze since it wasn't attached to anything. The more difficult task was removing the plastic rail guard for the top rack. With some elbow grease and ingenuity, I finally figured out that it must be tilted prior to being popped out of its socket. Follow the same procedure after replacing the rack.
Was this instruction helpful to you?
Thank you for voting!