66517349300 Kenmore Dishwasher - Instructions

When my dishwasher stopped working I went to the local appliance parts store with the entire button panel. I explained my situation to them, and the response was that I needed a new control panel -$68 and a week wait. So I ordered it. When it came in I noticed it was missing a button for the rinse only cycle. The parts guy said that maybe it was a problem with the parts vendor and ordered another one from their other vendor. In the mean time I installed the new control panel just to see if I would get any lights (no luck). A week later the new control panel came in - still no rinse only button. I got my money back and went home to see what I could find online. I ran across PartSelect - saw several comments describing my exact problem, and ordered a new fuse kit ($15). I put the original control panel back in, put in the new fuse (which took only 2 days to get to me!) and sure enough - problem solved.
Thanks PartSelect you have a great site with lots of useful information!

Steve in Colorado

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

We took off the old one by disconnecting everything and put in the new one an re-connected everything. Aligning the pump was a little difficult.

just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks

Easy to do. Less than fifteen minutes total and only tool required was a screw driver. Simply pulled out the old gasket by hand and then pressed in the new one with the screw driver. Anyone could do this.

I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

To perform this repair do the following:
1.) Turn off power to the dishwasher
2.) Turn off water, disconnect the water supply and drain using adj. wrench and/or nutdriver, remove any contents from inside
3.) Remove screws (2) from underside cabinet, remove kick plate from bottom by removing two (2) screws there, pull out washer gently providing slack to drain hose and water line
4.) Gently place washer on side, do not invert or lean on the front side, water may enter control panel and damage it
5.) Remove the water line from Inlet valve using adj. wrench
6.) Disconnect both wires from solenoid.
7.) There is one metal screw holding the valve in place, remove it with a nutdriver, slide valve assembly out.
8.) Remove the 90 degree brass angle fitting from old valve, this may require some effort. Using thread tape, install fitting on new valve assembly.
9.) Replace parts in reverse order, using thread tape on any additional water line fittings requiring it, restoring water and power last.
10.) Run a test wash and check for leaks.
Hope this helps, it did appear to fix my problem.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

Took me longer to find my tools than to do the repair. DId have to call the PartSelect 800 # while making repair but woman there read to me a note in their system about a redesign of the replacement part that explained exactly my question. She was VERY helpful. I will not be calling the appliance repairman again!

Drained washer with hand pump. Thermo fuse had blown. Removed control panel and substituted a 15 amp automotive ATC fuse, shimming the blades with aluminum foil. Removed dishwasher from counter niche. Tipped dishwasher, removed and inspected drain pump and recirculating pump. No apparent problems noted. Temporarily rerouted supply and drain lines and restarted. Grinding noise clearly came from the drain pump. Ordered new drain pump and replaced.replaced 20 amp thermo fuse.

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.

Screwed in new cap