36314061791 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carrell from Cochranville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap missing
installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy
wife happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Dallas, TX
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set, Wrench set
Thanks for sending the correct part. You guys did a great job.
Just put the part on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Cypress, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Upper rack kept dropping from the wheels when we pulled it out
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from TAMPA, FL
- Parts Used:
- WD13X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door latch broke
Removed the old one from its slot and slid the new one into it.
No instructions needed.
No instructions needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dameon from SMYRNA, DE
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dishwasher would not start
Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ROLESVILLE, NC
- Parts Used:
- WD21X10261
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from UPPR CHICHSTR, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Asok from HELOTES, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from LACONIA, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
poor dish washing
Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frederick from auburn, CA
- Parts Used:
- WD08X10016
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
water leak
stripped old gasket from around the door (easy part)
instructions said to remove two screws from the bottom of the door to allow you to fit the gasket around the bottom
this was not too easy as you cannot get see the inside of bottom end of the door
I ended up removing the other door screws and this allowed me to fit the gasket quite easily
one tip tape the door lock immediately after removing screws as the lock assembly is not attached to the door
final step was to make sure the gasket was seated all around as my first wash had a slight lead
by pushing on the door after the door was locked cured the problem
instructions said to remove two screws from the bottom of the door to allow you to fit the gasket around the bottom
this was not too easy as you cannot get see the inside of bottom end of the door
I ended up removing the other door screws and this allowed me to fit the gasket quite easily
one tip tape the door lock immediately after removing screws as the lock assembly is not attached to the door
final step was to make sure the gasket was seated all around as my first wash had a slight lead
by pushing on the door after the door was locked cured the problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Oshkosh, WI
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor froze up on dishwasher
Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheri from St.Cloud, MN
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Motor / Pump berrings out
Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from CAPE CORAL, FL
- Parts Used:
- WD28X31818, WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted dishracks
very simple pull out the old and push in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hillsborough, NC
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Put lower rack in
Took old rack out put new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from McMinnville, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Damaged rinse agent dispenser
Unscrewed old one and installed the new one.
Was this instruction helpful to you?
Thank you for voting!