6651576581 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Phil from Ft Lauderdale, FL
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken rollers
simple, simple, simple ! popped off the old ones, snapped on the new ones. Thanks !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from La Canada, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken wheel
I snapped the old ones off & snapped on the new ones. It couldn't have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Washington, MO
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken wheel on lower rack
i used a screwdriver to pry off the old wheels then snapped on the new ones.
This was the easiest repair I have ever made on an appliance.
This was the easiest repair I have ever made on an appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BRUSH PRAIRIE, WA
- Parts Used:
- 675611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replaced broken door spring
This repair should have been rated "Easy" but because of a) the age of the dishwasher - 25 years and b) the close quarters to replace the spring, it was a bit of a challenge. If I could have pulled the dishwasher out a few inches, replacing the spring would have been a snap. But because of new flooring on top of existing flooring, that wasn't possible. Also the side cabinets were so close that getting a pair of pliers in there to hook the spring onto the door was tough. Ended up cutting out some cabinet facing that wasn't going to effect the look of things in order to get my hands and tools in there to get the hook end of the spring on the door. After I finally got it on and replaced the kickplate, sat back and had a cold one. Whew!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOUG from KENTS STORE, VA
- Parts Used:
- W10311986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower dishwasher rack was deteriorating (extensive rust) and needed to be replaced
The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from KINGSPORT, TN
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
i had a leak under the dishwasher when the pump turned on.
I replaced the seals per the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from JUPITER, FL
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rochester, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Rack Was Rusting Out
Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from SPRINGFIELD, IL
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
All rollers missing on lower rack of dishwasher
The brackets that held the original wheels were still on the rack. They were easily pulled off the rack. The new assembly did not look like the original part. It was not difficult to see how they fit onto the rack. The only caution is to press the top part of the new assembly onto the frame before snapping the rest of the new piece into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shreveport, LA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replaced four lower rack on a whirlpool dishwasher.
I prayed old wheel assembly’s off with the claw end of a claw hammer. Carefully snapped on the new assembly’s which were a little tricky to align. Went well, took about 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from ELGIN, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
my old lower dishwasher rack was rusted out and some parts broken.
Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.
ooks beautiful and works perfectly.
Could have used some directions though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from TUCSON, AZ
- Parts Used:
- WP3367910
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rubber around the cap assembly was torn
I pulled the basket out, pulled the cap and connector assembly off with ease, no tools needed, it comes right up, and put the new one on. Put the basket back in and it works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from GREENVILLE, MI
- Parts Used:
- 4317933
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
all of the old rollers were missing.
the design of the new roller kit was a little different than the original. took a minute to figure the installation. all went well. the new roller assembly fit the 30 year old dish rack
Was this instruction helpful to you?
Thank you for voting!