66514703N511 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Glenwood, MN
- Parts Used:
- W10807920
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced silverware basket
No brainer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Nottingham, MD
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tines on top rack of dishwasher would not stay up
simple...a female did it!! Dealing with PartSelect was so easy...your was the only web site that made it super easy to find my part. Placed order and paid for it...part arrived the next day!! Sent web site link to hubby too. When we need parts again for any applicance in our home, we will check your site out first!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from AVONDALE, AZ
- Parts Used:
- W11177741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water leaking from this appliance onto the floor
removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers
No Leaks!!
Saved the cost of a new dishwashers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from HARLINGEN, TX
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lower dish rack needed replaced
Removed new from box and installed rollers as instructed that's all there was , very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from BETHESDA, MD
- Parts Used:
- WPW10195417
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the rollers broke of on the lower dish rack
Snapped the old one off and snapped the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from ESCONDIDO, CA
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack was rusting, staining dishes.
Rolled out old, rolled in new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from WESTERVILLE, OH
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
all rollers fell off. lower rack was hard to move when full
Purchase 4 roller wheel assemblies and installed them with only a screw driver to open the tangs. quick and easy and rack rolls smoothly inside the dishwasher. Rather expensive $58 per roller assembly and hopefully these last the lifetime of the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- garret from Fair Haven, NJ
- Parts Used:
- 8194001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door spring cable broken
You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from E GRAND FORKS, MN
- Parts Used:
- WPW10327249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
High pitched noise when the washer filled at the beginning of the cycle.
Watched the video, it went as advertised. Easy repair and the noise is gone.
Was this instruction helpful to you?
Thank you for voting!
Top rack wheel broken causing rack to fall when extended too far.
watched instructions and proceeded. Parts were self evident after watch ing video. Easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PITTSBURGH, PA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Unwanted water.
A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CONVOY, OH
- Parts Used:
- W10728159
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken bottom rack
Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from PRESCOTT, AZ
- Parts Used:
- WPW10653840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door would not latch shut
Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.
Was this instruction helpful to you?
Thank you for voting!
The wheels broke off from the rack hangers.
The replacement kit came with no instructions in the box, so I found the instructional video online. This video pointed me in the right direction so I could take it the rest of the way myself.
Here is the link to the instructional video i used
https://www.partselect.com/PS10065979-Whirlpool-W10712395-Upper-Rack-Adjuster-Kit-White-Wheels-Left-and-Right-Sides.htm
Even though I purchased the end cap pieces for the roller stops, I was able to reuse the original pieces so these are to be keep for spare if required.
This was a very cost effective repair instead of replacing the entire rack assembly.
NOTE: The original Wheel bracket was a molded plastic piece, but the replacement is Stainless Steel. This had no impact on the functionality, but did add a small amount of noise during the wash cycle. My belief is this is the water hitting the steel vs. hitting the plastic.
Here is the link to the instructional video i used
https://www.partselect.com/PS10065979-Whirlpool-W10712395-Upper-Rack-Adjuster-Kit-White-Wheels-Left-and-Right-Sides.htm
Even though I purchased the end cap pieces for the roller stops, I was able to reuse the original pieces so these are to be keep for spare if required.
This was a very cost effective repair instead of replacing the entire rack assembly.
NOTE: The original Wheel bracket was a molded plastic piece, but the replacement is Stainless Steel. This had no impact on the functionality, but did add a small amount of noise during the wash cycle. My belief is this is the water hitting the steel vs. hitting the plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from THE WOODLANDS, TX
- Parts Used:
- WPW10195840, W10712395
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The wheels on the upper rack kept coming off
What I needed were simple clips to lock in the wheels. I ended up getting a kit that required replacement of the roller tracts on both sides of the upper rack. The instructions were terrible. The repair took far more time than it should have. Once one side was fixed it was easy to fix the other side. By then I had worked my way around the muddled instructions.
Was this instruction helpful to you?
Thank you for voting!