2213099N413 Kenmore Dishwasher - Instructions

Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.

Turned the dishwasher in its side. Used the video step by step. This is why we purchased from this site

lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.

When we ordered the part the first time, we pulled the model number from the documentation instead of the machine. We got the wrong part the first time. The people at Parts Select were very knowledgeable and helpful when we called. After we pulled the model number from the machine, they sent the perfect part that popped in with no problems.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

removed and installed cords with screw driver

After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.

Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.

Replaced door latch

Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

after that every thing went very well

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!