66514819N610 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- edward from sullivan, OH
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door of the dishwaher banged open
Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from NEENAH, WI
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
old wheel assembly broke
locate lock tab and gently press
slide off the old assembly.
align and slide the new assembly on.
the lock tab is sometimes hard to push in, if you struggle with pushing it you can either break it off the old assembly or use a small flat head screwdriver to gain leverage.
slide off the old assembly.
align and slide the new assembly on.
the lock tab is sometimes hard to push in, if you struggle with pushing it you can either break it off the old assembly or use a small flat head screwdriver to gain leverage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from LUMBERTON, TX
- Parts Used:
- WPW10327249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water flow to dishwasher
Removed lower kick panel and there it was on the left hand side. Removed the waterline and removed the mounting screws. Disconnected the inlet waterline into the dishwasher. Removed the bad inlet valve and replaced in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Galveston, TX
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing tine pivot
Pushed to be into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from CANONSBURG, PA
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheel broke
Removed the new part and forced fitted the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Scottsdale, AZ
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A bracket was missing on the top rack of dishwasher
Easy. Part just snapped in and took all of about a minute. Now the top rack doe snot slide back and forth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from WILLCOX, AZ
- Parts Used:
- W10807920
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Worn silverware drawer
Perfect match
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- K A from WESTLAKE, OH
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel of lower rack snapped off. After repeated attempts to put back on, decided to replace the assembly. There are actually 4 assemblies on the lower rack
Placed the entire drawer on the kitchen counter. Plastic part came off. New one installed in less than 10 seconds.
Piece was expensive but not nearly as much as a dishwasher repairman!!
Piece was expensive but not nearly as much as a dishwasher repairman!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from FAYETTE, OH
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tine on rack was rusted and needed to be replaced.
Just replaced it in the notches that held the rusted tine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from ELGIN, IL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky dishwasher door
Just like the video; remove the 2 nuts off the kick plate, remove the 2 screws under the counter, pull the unit out, ease the spring off the cable, nut drive the pully assembly's off, install the new ones, place new rope/cable from the door arms onto pullys, attach the spring, push the unit back into place, replace screws and the kick plate. Took 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST NEWFIELD, ME
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
spring cable end broke
followed your very well done video clip exactly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LONGVIEW, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The dishwasher door wouldn't hold in any position but went all of the way open.
You said the repair was easy and would take around 5 minutes to perform. You were spot on and the instructional video really helped do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JIMMY from ST GEORGE ISL, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cord on balance mechanism broke.
pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominic from AURORA, IL
- Parts Used:
- WPW10195417
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old wheels were falling off
Very simple. Snapped the old wheel assembly off. Then snapped the new wheel assembly on. Done!
Was this instruction helpful to you?
Thank you for voting!