66514819N610 Kenmore Dishwasher - Instructions

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

I watched online repair video for replacing the part. 3 different clips held the part in place. Video showed how to properly remove each clip & also how to put them back on once part is replaced. Video was immensely helpful because I was afraid I break something else trying o remove them! I ordered & replaced the part by myself without help from my husband. My daddy would've been so proud. :)

Removed old part and replaced with new part

Replacing the rear wheel assembly isn't as easy as replacing the front, which took 5 minutes. You have to align the tine row, so it takes a few minutes more. But I'm a tiny woman with long nails, and if I can do it, you can do it!

Just watch the video, follow the directions, and you can't go wrong.

Removed the old rack clips from the top rack, freeing the rack and removed the bracket holding the adjustable bracket

Replaced the rack bracket and hung the rack back onto the rails

Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).

Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.

As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.

When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.

The repair was similar to the very good video provided by PartSelect. However, I did make a few changes. The new rack was slightly different in the front side compared to the old rusted rack. After I removed the old rack from the dishwasher, I placed the two racks side-by -side to make sure they were compatible. They were identical in the rear structure and overall size, so I proceeded to change out the wheel racks, rack height adjusters and upper wash arm to the new rack. I suggest transferring each part one at a time so you can get the spacing correct. Also, in my case, many of the items needed to be washed with water to remove soap buildup in these parts before moving to the new rack. I would also suggest putting the upper wash arm (needed in this case) on the new rack last. The total job took me about an hour including washing or rinsing all parts and reassembly. This is an easy job, just take your time and do one item at a time so nothing gets mixed up. I used a drill driver to remove a total of 4 Phillip head screws for the rack height adjusters but a regular Phillip head screw driver would work as well.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Popped damaged/worn wheel assembly off, snapped new ones in. Easy peasy

I did a Youtube search and discovered there were a couple that showed the replacement in detail. I watch the entire process once and then had my laptop beside the upper rack and paused the video after each step. That worked well

Removed old housing parts and replaced them with the new parts I ordered. Very easy

I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

Great fit. take out old one and drop in new one. Piece of Cake.

Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.