66512776K314 Kenmore Dishwasher - Instructions

All four original wheel assembly's were difficult to pop out so used pliers and cutter to brake original part and remove it. Nothing on the original wheel assembly was needed for the repair so braking them off was ok. The new wheel assembly parts, with two wheels on each (4 total), two wheel assembly's on each side of the rack, were easy to install- no tools needed. Each wheel assembly just popped right into place.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

remove 2 locks on metal roller guides. remove top basket. turn upside down on counter.remove spray arm by pryng one side in and lift out then push other side down and the out. install same as removal. line spray arm and turn clockwise til you hear a click.install basket and install locking plugs.

Removed old part and replaced with new part

Snapped the new stops on. It took about 2 minutes.

I give you a 5-Star customer review.

When the button holding one of the rollers in place fell off, I was lost, didn't know what to do. Then I found you online and called, there was virtually no waiting time on hold, and a very helpful representative quickly found the correct part and ordered it for me. It arrived in only 2 days! Removing the old roller assembly with a screwdriver was a easy, it took 2 seconds. Snapping the new one into place was more difficult -- it took me about 5 minutes to figure out how to do it, and an instruction diagram would have been helpful, but that was a minor inconvenience.

I cannot thank you enough. Excellent service! Definitely 5-Stars!

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...

Pulled off old seal. Pressed into groove the new door seal. No parts required.

parts were an exact fix to my problem the on line video was perfect repair was done in under 30 min
thanks
keith
bluffdale, utah

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.