66513173K706 Kenmore Dishwasher - Instructions

just move the machine out and replace the string. this site is very reliable and and great company. since the dishmachine door cannot be closed, we first order door strike, ,,,, still doesn't work after installation. and return all parts and order the balance kit, now works fine after. we appreciate your help

Unscrewed mounting screw at top and bottom of duahwasher, pulled out dishwasher could see the pully on one side had broken. installed new part put dishwasher back in place and rescrewed mounting screws.

Started the rope onto the top holder, threaded the rope around the rollers and using the pilers pulled the spring forward to attach the other end of the rope.

Disconnect top screws
Pull dishwasher out halfway
Notice how the other side is connected
Thread cord, use pliers to pull spring to connect.

Shut off elec. and water. remove bottom plate and 2 screws holding the unit to the counter top.
disconect elec wires to unit and remove water line.
Pull unit out from counter and replace cable to spring the same way as the unbroken side.
Slide unit back and reverse hookup.
My only problem was that the part they sent me was about a 1/2" shorter the the original and the door is hard to open.

The repair itself was relatively easy. I basically only had to remove the two screws that were securing the diswasher to the cabinetry, disconnected the water line and extended the diswasher out approximately 10 inches. I then replaced the part by hooking the new cable assembly to the spring and using pliers expanded the spring so I could snake the other end of the cable through the pulleys and attach it to the door. The otherside was my guide. This part should be modified to replace the two plastic ends with metal counterparts. This would allow the part to have a longer life especially in my case since the plastic end broke and not the cable itself.

Pulled dishwasher from under the counter and replaced the plastic part with the new part and attached the new cord to the door spring and to the replacement plastic part. replaced the dishwasher under the counter and replaced the kick plate. All Done.

Received the part. No instructions came with it. Luckily it was pretty simple to figure out. i removed the appliance from under the counter, saw how the part was attached on the other side and simply replaced the other side that was broken. Easy.

The video does a great job explaining the repair. I took the unit completely away from the wall and put it on its side, which I recommend. Only problem I had was getting the new part in the correct orientation to lock... try to pay attention to how the failed pump is facing when you remove it.

I ended up replacing the supply line as well as just moving it around caused a drip leak, guess it was about to fail. Pro tip: don't remove the old line until you have the new line in hand... but that's a story for another day.

1st pull dishwasher out. attach the new cable to the spring. reinstall the spring on the frame. Use pliers to pull slack in the cable to attach the cable to the door. The hardest thing about the install was putting the screws in the side of the dishwasher to the cabinets.

Get a piece of stiff wire (medal close hanger) cut a Short piece and take a tool and roll a half circle on each end making the link length you need then attach the lanyard to the spring

Used new seal and glue. Your company was great. However, the part had changed and did not agree with the installation instructions. After calling the friendly person at your company to determine if I had the right part(it did not have a white stripe on it and did not look like the old part), I followed the instructions and it was easy. No leak-happy family.

My 2 yr old sat on the dishwasher door while it was open. It snapped both the links on the door causing the dishwasher door to drop every time it was ajar. It was a real danger to the kids or to anyone else unaware of the door given its weight.

I ordered the part from Part Select based model and some of the posts that it was something you can do yourself. Park Select was outstanding as got the part next day and got direction from others (thank you). I did not have either side of the door working so no real gauge but finally understood how it worked once I did a search online for a picture.

Recommendation: if both links (rope) are broken, you will need to hunt down the springs on side/back of machine. The part with small hole connects to the spring, the other to the door. Make a reverse S with the rope through the pully system for tention. I did not initially do the reverse S and the part popped of the door once I closed it. Otherwise, easy thing to do and certainly do not need a repair person.....if you need picture, do a search on dishwasher door pully system

repaired exactly as your video described......hardest part it getting unit out from under cabinet and back in.

Video was great help. Replacing the balance parts was easy. My wife and I are in our 80's. Mobility is difficult when it comes to working on the floor. Between the two of us we spent the majority of our time just getting up and down,