66514813N611 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cassie from RIVERDALE, CA
- Parts Used:
- WPW10546503, WPW10250162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replacing broken adjuster housing cover.
Take out the upper dishwasher rack. Place the adjuster towards the back of the upper each place attachment clips to secure adjuster and the adjuster clips to the back of the housing. Check to back sure adjuster move up and down and click back into place. Your installation is complete. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from CLARKSVILLE, TN
- Parts Used:
- W10919676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
This did not fix the rack issue
It was wrong part. Visual in diagram does not clearly show what needs to be replaced. Old part just broke so we do not know what needs fixing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from WESTFORD, MA
- Parts Used:
- WPW10340542
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
The Broan downdraft vent fan turned itself on at random times and ran continuously without input.
I could not effect a repair because the parts did not arrive on the promised date and after several calls I still do not know when they will arrive or even if they have been shipped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from WAKE FOREST, NC
- Parts Used:
- WPW10327249
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
No water was entering the dishwasher.
Disconnected the water hose entering and one electrical plug alone with one screw that holds the valve to the machine. Replaced the old with the new and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from NEENAH, WI
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
old wheel assembly broke
locate lock tab and gently press
slide off the old assembly.
align and slide the new assembly on.
the lock tab is sometimes hard to push in, if you struggle with pushing it you can either break it off the old assembly or use a small flat head screwdriver to gain leverage.
slide off the old assembly.
align and slide the new assembly on.
the lock tab is sometimes hard to push in, if you struggle with pushing it you can either break it off the old assembly or use a small flat head screwdriver to gain leverage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from sullivan, OH
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door of the dishwaher banged open
Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from LUMBERTON, TX
- Parts Used:
- WPW10327249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water flow to dishwasher
Removed lower kick panel and there it was on the left hand side. Removed the waterline and removed the mounting screws. Disconnected the inlet waterline into the dishwasher. Removed the bad inlet valve and replaced in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from CANONSBURG, PA
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheel broke
Removed the new part and forced fitted the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Scottsdale, AZ
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A bracket was missing on the top rack of dishwasher
Easy. Part just snapped in and took all of about a minute. Now the top rack doe snot slide back and forth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Galveston, TX
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing tine pivot
Pushed to be into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from WILLCOX, AZ
- Parts Used:
- W10807920
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Worn silverware drawer
Perfect match
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rancho Cucamonga, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door 'spring' broke...heavy door would fall hard when opened.
First we removed the two screws up under the countertop that secured the dishwasher in place. Next we pulled the d/w out from under the counter, having to unplug the power cord and feeding the drain hose into the d/w cavity from under the kitchen sink to allow this. On each side, attached to a metal spring was a nylon cord with plastic attachments that ran through two plastic pullies/wheels. The plastic piece on one of the nylon cords had broken...only on one side, so we were able to just look at the 'good' side to see how to attach and string the repair part through again. We pushed the d/w back in, made sure the drain hose under the kitchen sink wasn't kinked by pulling it back under the sink from the d/w cavity, plugged it in, replaced the two securing screws and were done. The old cord running through the pullies had always creaked when the door was opened, so while the d/w was out, we coated it w/ WD40. Piece-of-cake!
Was this instruction helpful to you?
Thank you for voting!