66514813N611 Kenmore Dishwasher - Instructions

I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...

In looking at the parts catalog the part I needed didn’t state left or right side piece. I understood that the same part was used on both sides. Knowing the other side may fail also I ordered (2) pieces. Once they arrived I took apart the surrounding element using a screw driver to pop the enclosure apart carefully. I noted where each clip went and re-assembled the enclosure.

No instructions were given but I found a YouTube video of the repair and it took less than a minute to install.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

I took the old wheel assembly off and snapped the new wheel assembly on. It’s that simple. Note the dishwasher rack needs to be empty. Very pleased with this site. Parts came super fast.

pushed the new retainers in the holes and we are set to go

Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.

The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

We watched videos on this repair but they didn't matter. All we did was remove the lower rack of the dishwasher. To remove the broken assembly we put pressure behind the wheels pulling them out and up - it popped right off. To install the new wheel assembly, it was easy to see where to align the part and my husband snapped it back in. No tools. Easy peasy.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

Popping out the old tine rows was very simple and required no tools. The only issue was that the spacing of the replacement tines was different from the original parts and there was not enough space between the tines and the basket to snap the clips back on to hold the tine row. I went to my band saw and cut the extended ends off of the clips and then they snapped into place perfectly. This would have been a 20 minute, no tool job if I didn't have to run to the band saw.

Ordered p/n PS10057154, sold as a kit of TWO upper rack tine rows. I received one. Customer service issued a return tag and ordered a second kit, which again was supposed to be two rows. Replacement order arrived with just one. Fortunately, I had expected this and had not yet returned the first kit. Called customer service and told them not to expect the return of the first order.

This kit is sold as fitting several models of Whirlpool and KitchenAid dishwashers, which I verified that my KA was on the list. A minor installation problem occurred when I discovered that the upright tines of this kit don't have the exact same spacing as the KitchenAid originals. The upright tines need to be exactly half the distance between each of the crossbars on the rack below in order to install the three retaining clips found on each row. With the spacing of these tines, there wasn't quite enough room to install the clips. Fortunately, the retaining clips were manufactured with an excessive amount of shoulder on each one. Trimming off the excess material with a fine-toothed hacksaw blade made the clips narrow enough to be used without compromising their ability to hold the tine rows in place. I've used the machine several times now and the clips are holding everything in place as expected.

[img]https://i.ibb.co/9TQB3mC/clips.jpg[/img]

Upper tray removed and each rack adjuster removed and replaced one after the other. Only tool was screwdriver. Only knowledge was from the online videos. Only took 30 minutes or so. The repair could have been done more quickly if I wasn't fearful that the smaller plastic parts would break when pulled or pried away from the rack adjuster. The only mistake was not making sure the adjuster tabs were fully engaged in back and clicked in the front attachment.