66514823N511 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Galveston, TX
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing tine pivot
Pushed to be into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominic from AURORA, IL
- Parts Used:
- WPW10195417
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old wheels were falling off
Very simple. Snapped the old wheel assembly off. Then snapped the new wheel assembly on. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from WILLCOX, AZ
- Parts Used:
- W10807920
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Worn silverware drawer
Perfect match
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Drexel Hill, PA
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original door seal came out while emptying dishwaher. It was pretty messy so i ordered a new one.
I just followed the directions on the video that was part of the pictures for the door seal. I made sure that the channel was clean and the new seal pressed right in. i wish I had checked this site before I called a repairman, who wanted to charge me over $400 for a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LONGVIEW, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The dishwasher door wouldn't hold in any position but went all of the way open.
You said the repair was easy and would take around 5 minutes to perform. You were spot on and the instructional video really helped do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JIMMY from ST GEORGE ISL, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cord on balance mechanism broke.
pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from ELGIN, IL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky dishwasher door
Just like the video; remove the 2 nuts off the kick plate, remove the 2 screws under the counter, pull the unit out, ease the spring off the cable, nut drive the pully assembly's off, install the new ones, place new rope/cable from the door arms onto pullys, attach the spring, push the unit back into place, replace screws and the kick plate. Took 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST NEWFIELD, ME
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
spring cable end broke
followed your very well done video clip exactly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from METHUEN, MA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door became heavy on one side
Pulled dishwasher and removed existing springs and attached rope. Ordered the part needed and replaced it somewhat easily. There is a lot of tension because of the spring on the door. Once part was installed we were ready to use our dishwasher right away. Even though the rope was broke on only one side - we replaced both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- K A from WESTLAKE, OH
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel of lower rack snapped off. After repeated attempts to put back on, decided to replace the assembly. There are actually 4 assemblies on the lower rack
Placed the entire drawer on the kitchen counter. Plastic part came off. New one installed in less than 10 seconds.
Piece was expensive but not nearly as much as a dishwasher repairman!!
Piece was expensive but not nearly as much as a dishwasher repairman!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from FAYETTE, OH
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tine on rack was rusted and needed to be replaced.
Just replaced it in the notches that held the rusted tine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Mansfield, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door pulley rope broke
Turned off power to dishwasher.
Removed screws from dishwasher retaining clips.
Pulled out dishwasher.
Removed broken rope.
Installed replacement and put everything back together.
Very easy repair. The spring is very strong and extra hand can be helpful, but not required.
Removed screws from dishwasher retaining clips.
Pulled out dishwasher.
Removed broken rope.
Installed replacement and put everything back together.
Very easy repair. The spring is very strong and extra hand can be helpful, but not required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Petaluma, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No spring tension to dishwasher door.
After pulling the dishwasher out of the cabinet (2 screws held brackets to the underside of the counter - accessible when the door is open), I removed the broken link pieces, re-attached the springs and routed the link line around the pulleys. No need to re-set the spring tension as it was adjusted properly.
Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary.
I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.
Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary.
I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sophie from Brooklyn, NY
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door got very heavy and wouldn't support itself
Removed 2 screws that held unit under counter. Slid diswasher out about half way; reattached metal spring in back and removed broken string. Attached replacement string to spring and threaded through wheels (copying other side), then attached string to door. Tada! Done. Will never pay a call-out fee again (for this problem anyway...)
Was this instruction helpful to you?
Thank you for voting!