66514754N511 Kenmore Dishwasher - Instructions

The upper rack adjuster kit was replaced exactly as the video showed. I felt it was not very complicated and the new parts look more hefty then the original parts.

Front track stops was just a matter of snapping them into place.

I purchased this misguided by the official response to "Doug" on April 17, 2018, which at the time was labeled as "most helpful". This is NOT the little grommet in the center. This is a big grommet that goes no the supply pump. This is #14 in the diagram. (#15 is actually the clamp that holds it). If you are looking for the little grommet that goes on that stem on the central recirculation pump, that part is not available, it only comes fused on the sump, and for replacing the sump you have to disassemble the whole bottom part of the dishwasher, pumps, sensors, valves, hose...even this big grommet. A lot of work, and since you are at it, you might want to replace both grommets. If you need THIS big grommet (#14) only, then it is not so much work, just take out one clamp, one connected cable, and the grommet to replace. But check if your machine has reusable clamps, because if not, you might want to order a new clamp. Good luck!

I followed the installation instructions included with the kit, they are not the clearest or the most detailed but they allowed me to finish the job in under 15 minutes. Only one side was broken but I replaced both sides in the time. Not a big job and very easy for a DIYer with average mechanical ability.

The install video was invaluable, and made installation a breeze. Unfortunately it did not include instructions to remove the original adjuster — which was of a slightly different design as the replacement. I eventually got the old part off using a screw driver to pry the plastic snap connections apart.

I order parts online from partselect, watched a YouTube video for five minutes that gave detailed instructions on how to install new upper rack assembly and in less than 20 minutes repair was complete. Piece of cake!

Removed old gasket, cleaned track and replaced gasket-also quit using Cascade pellets and went back to using Cascade powder with a numerical "rating" of 6. The pellets of even 10 caused the washer to leak, obviously too much foam would not float the float to actuate the pump.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

It was easy! First I ordered the expensive replacement parts on line. The parts arrived in one week. I was able to slide the old drawers out, slip a few parts off of the old drawers, snap them on and slide the new drawers in place!

My KitchenAid dishwasher's upper dishrack had several places that were completing rusting out, just leaving the skins of the plastic coating in place. I ordered the upper dishrack - just the dishrack, none of the clips or other items shown in the schematic - and installed it pretty easily. One caution - this is JUST the upper dishrack. If you have two rows of tines that are clipped in and flip-flop back and forth on the left and right wider sides of the rack, you will need to order one or two pieces of part # PS 898500 as well. One of my tine rows was in salvageable shape, so I only needed to order one (in a second order upon discovering I it wasn't included). It wasn't difficult to figure out how the clips could come out and snap back in place. Just be careful, know that these are just plastic items and can break easily.

Followed a video, pretty straightforward. Be sure to clean all the area. My husband used cotton swabs to clean all the gunk.

I did this repair after watching the video on PartSelect's website. It went exactly as it was shown on the video. The video did not show removal of the old components. None of the old adjuster parts need to be saved for re-use so if they break upon dis-assembly it does not matter. This project went about as well as a project could. I certainly recommend this repair using the parts on PartSelect's website. Very good!

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

Listened to the video from Parts Select which was on the part number where it was ordered from. It was a very well done video.

repair was easy. Pictures in the instruction not clear had to refer to old parts

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.