66514793N510 Kenmore Dishwasher - Instructions

Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.

Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).

Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.

As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.

When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.

The rubber door seal was easy after watching the video. I key point however is that you do have to stretch the seal just a little bit. The video says not to. If you don't like I didn't originally, the seal will only extend from one side to the other without about an inch excess that folds on the bottom of each side. The door still leaked a little without the excess folded on each side. I did one side at a time and pulled out the new seal along the side before curving to the top, and just stretch it slightly to allow the excess. This stopped the leak.

The lower door seal was ok to do. The most important step there is to remember how the front door panel is installed. Taking pictures before and during removal may help. It is awkward to do by yourself, but can be done. I found that putting a balled-up towel at the top of the door helps when trying to reinstall the front panel.

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

Removed old housing parts and replaced them with the new parts I ordered. Very easy

Great fit. take out old one and drop in new one. Piece of Cake.

I did a Youtube search and discovered there were a couple that showed the replacement in detail. I watch the entire process once and then had my laptop beside the upper rack and paused the video after each step. That worked well

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

Popping out the old tine rows was very simple and required no tools. The only issue was that the spacing of the replacement tines was different from the original parts and there was not enough space between the tines and the basket to snap the clips back on to hold the tine row. I went to my band saw and cut the extended ends off of the clips and then they snapped into place perfectly. This would have been a 20 minute, no tool job if I didn't have to run to the band saw.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.

pushed the new retainers in the holes and we are set to go

The old filter simply unscrews and the new one screws in.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.