58714242100 Kenmore Dishwasher - Instructions

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

The actual installation of the dispenser was a breeze. Just unscrew the 6 screws unplug the 2 electrical wires and put the new one in. The problem I had was removing and replacing the front panel of the machine. The metal facing had corroded onto the frame of the door and was difficult to get off. Replacing the door was just as much a pain as it had to be lined up correctly with 4 holes in the frame. Did it in the end everything works great. Cheaper than a whole new machine.

I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.

PartSelect is a life saver and I saved lots of money by not having to call a repairman.

Removed the rack out of dishwasher. Removed sprayer by removing 4 screws. Removed cover to pump propeller assy.by just lifting up on the cover. Then you remove 4 screws from the pump cover. Remove the propeller. Pull up on shaft and seal. Then when you replace everything just reverse the directions.

I read other descriptions on how to repair this item at this site. All were spot on. Simply unscrew the control panel (6 screws on inside of unit), then unscrew the two screws holding the latch in place (it's a one piece unit), then remove the (4) leads to the latch paying attention to where each of the colored wires goes...re-attach all screws and you are done. It worked like a breeze after I was done. I did forget to turn off the power to the dishwasher as I thought i did but due to the broken latch the unit wouldn't function so I misjudged it. Next time (hopefully there isn't one) I will make sure power is off. I didn't use the gasket but have it in case something leaks down the road. Took less than 10 minutes and my 11 year old son helped too!

Removed six screws to the front cover panel. Remove two star bit screws holding door latch assemble in place. Removed four wires. Attached four wires. Put the two star bit screws back. Reassemble front cover and put back six screws. Job Done!

I removed 6 screws, and the front top panel came off, which had the handle unit attached. It had 2 screws to remove, and 1 wire plug to pull out. I put the handle unit on, plugged the wire harness in and put the panel screws back in. It took about 5 minutes. I saved about $90.00. I am so glad I found this website. It is now in my FAVORITES

Removed about 7 screws, unplugged the wiring, plugged the new handle / switch in, replaced screws and I was done!

Took off 2 screws and took the old detergent holder off and put the new one on....Very easy...took all of 5 mins

Snapped the new one in. One second repair - like new.

Opened it up, replaced, closed it back. Didn't bother installing the gasket since that's still in good shape.

Snapped new wheels into place on the axel. New wheels were exactly like the old ones

So easy it shouldn't even count as a repair, really. The dishwasher, there when I bought the place, had a lower rack that wouldn't roll out as it should. That's because there were no wheels on the left side.

The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.

I actually didn't. I watched my husband replace the latch and gasket. All he used were screwdrivers to remove the panel on the inside of the door. The latch assembly had to plug in and two screens. He unscrewed, unflugged the broken unit, replaced it with the new by screwing in the two screens and plugging the the prongs into the panel. He then put the door cover back on. It took about 10 minutes and the dishwasher is as good as new!!

I snapped on the new roller and bingo! problem solved.