66512782K310 Kenmore Dishwasher - Instructions

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

We watched videos on this repair but they didn't matter. All we did was remove the lower rack of the dishwasher. To remove the broken assembly we put pressure behind the wheels pulling them out and up - it popped right off. To install the new wheel assembly, it was easy to see where to align the part and my husband snapped it back in. No tools. Easy peasy.

Laid on my side amd reach under unit

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

Had to remove 2 screws fastening dishwasher to counter. Also removed bottom faceplate to expose the legs and to be able to lower them. Other sites recommended disconnecting the drain and water line but I did not have to do that, I had enough slack in the lines. I got the dishwasher about halfway out of the cabinet and then was able to remove the 4 screws holding the right track. Put the new track in and was good to go. Problem was that the left track broke and fell off a few days later. Still was an easy fix and thanks to PartSelect it was not very expensive.

Great fit. take out old one and drop in new one. Piece of Cake.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

Upper tray removed and each rack adjuster removed and replaced one after the other. Only tool was screwdriver. Only knowledge was from the online videos. Only took 30 minutes or so. The repair could have been done more quickly if I wasn't fearful that the smaller plastic parts would break when pulled or pried away from the rack adjuster. The only mistake was not making sure the adjuster tabs were fully engaged in back and clicked in the front attachment.

Turned off water supply to the unit. Removed plastic cover at bottom front. I only had to disconnect the copper water line to slide the unit about 1/3 of the way out. I then was able to reach the wires, disconnect them and use a stubby box/open end wrench (5/8? don't remember for sure) to remove the plastic nuts. I then opened the door, removed the bottom basket and slipped the element right out. Installation of new part was reverse.

Ordered p/n PS10057154, sold as a kit of TWO upper rack tine rows. I received one. Customer service issued a return tag and ordered a second kit, which again was supposed to be two rows. Replacement order arrived with just one. Fortunately, I had expected this and had not yet returned the first kit. Called customer service and told them not to expect the return of the first order.

This kit is sold as fitting several models of Whirlpool and KitchenAid dishwashers, which I verified that my KA was on the list. A minor installation problem occurred when I discovered that the upright tines of this kit don't have the exact same spacing as the KitchenAid originals. The upright tines need to be exactly half the distance between each of the crossbars on the rack below in order to install the three retaining clips found on each row. With the spacing of these tines, there wasn't quite enough room to install the clips. Fortunately, the retaining clips were manufactured with an excessive amount of shoulder on each one. Trimming off the excess material with a fine-toothed hacksaw blade made the clips narrow enough to be used without compromising their ability to hold the tine rows in place. I've used the machine several times now and the clips are holding everything in place as expected.

[img]https://i.ibb.co/9TQB3mC/clips.jpg[/img]

Took the kick plate off without removing the the machine.
Reached in and turned the existing pump to loosen it. Then disconnected the wire.
Reversed the process to install the new pump.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Turned the dishwasher in its side. Used the video step by step. This is why we purchased from this site